Extron electronics TouchLink TLP 350CV Скачать руководство пользователя

Страница: 44 / 51

Reset Modes,

Button

Replacement,

Firmware Updates

Reset Modes

Button Kits

Button Replacement

Updating Firmware

LED
Reset
Menu

Figure 26.

Reset Buttons

The modes are initiated by pressing the reset button. Using
a paper clip, push through the reset access hole on the right
side of the faceplate as shown below.

NOTE:

The access holes are very small. Take care when

pressing the reset button to avoid scratching the
faceplate.

The successful completion of a reset is indicated by four
flashes of the reset LeD.

The TLP 350CV reset modes are initiated by pressing the
reset button on the front panel. See the table on the
following page for details.

Reset Modes

The TLP 350CV has four reset modes that correspond to four of the five
reset modes for the IP Link controllers.

TLP 350CV • Reset Modes, Button Replacement

Содержание TouchLink TLP 350CV




















































Результаты поиска

Содержание TouchLink TLP 350CV

Отзывы:

Похожие инструкции для TouchLink TLP 350CV

Бренды по названию

Популярные бренды

Extron electronics TouchLink TLP 350CV, Руководство по установке

Результаты поиска

Содержание TouchLink TLP 350CV

Отзывы:

Похожие инструкции для TouchLink TLP 350CV

Бренды по названию

Популярные бренды