Extron electronics TouchLink TLP 350CV Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 51

Extron electronics TouchLink TLP 350CV Скачать руководство пользователя страница 12

TLP 350CV • Prepare the Table

6

Cutout Dimensions

Cutout dimensions are available from extron as a router guide, printed dimensions for a
CNC wood router, and a paper cutout template for a reciprocating saw or jigsaw. If using
the router guide, follow the instructions included with it. Printed dimensions are available in

Specifications on page 36

.

The opening in the table for the Cable Cubby should be cut only by licensed and bonded
craftspeople. exercise care to prevent scarring or damaging the furniture.
ensure the table surface is at least 3/8 inch (0.375 in) (0.95 cm) thick.

WARNING:

Make certain the correct cutout dimensions are being used before

proceeding. extron electronics is not responsible for improperly
positioned Cable Cubby models.

Double-check before you cut:

z

If using a routing template, be certain it is the correct template for the TLP 350CV.

z

If using a CNC router, be certain the correct dimensions for the TLP 350CV are entered.

z

If using a reciprocating saw or jigsaw, be certain to use the correct paper template for
the TLP 350CV.

z

be certain the cut is laid out in the desired location.

z

be certain the cut is laid out so the touch panel is oriented as desired.

«
...
10
11
12
13
14
...
»

Содержание TouchLink TLP 350CV




















































Отзывы:

Нет отзывов