Extron electronics TouchLink TLP 350CV Скачать руководство пользователя

Страница: 49 / 51

Click

File | Open

and navigate to the folder where the firmware file is located. Click on

the file to select it, then click

Begin

192.168.254.254

V00*00 A0*X**

60-xxxx-01

1.00.00xx

Figure 30.

Firmware Loader, Begin Firmware Upload

The firmware transfer takes approximately 3 minutes.

when the

“Transfer Complete!”

message appears, click

File | Exit

to close the

Firmware Loader.

Updating Firmware Using GUI Configurator

Power on a computer with internet access and ensure the computer and the TLP 350CV
are connected to the same network. If necessary,

install the Extron Firmware Loader

utility onto the computer (see step

of the previous section).

Download the firmware upgrade. (See

Obtaining the Firmware Update File on

page 41

.) Make a note of the folder where the firmware file is saved.

Open GUI Configurator, then select the Firmware Loader by clicking on “

Firmware

Update Manager...

” in the

Tools

menu.

Figure 31.

Opening Firmware Update Manager from GUI Configurator

Follow steps

from the previous section (“Updating firmware using the extron

Firmware Loader utility“).

TLP 350CV • Reset Modes and Button Replacement

Содержание TouchLink TLP 350CV




















































Результаты поиска

Содержание TouchLink TLP 350CV

Отзывы:

Похожие инструкции для TouchLink TLP 350CV

Бренды по названию

Популярные бренды

Extron electronics TouchLink TLP 350CV, Руководство по установке

Результаты поиска

Содержание TouchLink TLP 350CV

Отзывы:

Похожие инструкции для TouchLink TLP 350CV

Бренды по названию

Популярные бренды