Extron electronics TouchLink TLP 350CV Скачать руководство пользователя | Manualshive

Страница: 13 / 51

background image

Mounting the

Enclosure

This section includes the following topics:

z

Installing the Power Module, Cables and AAPs

z

Mounting the Enclosure

Installing the Power Module, Cables and AAPs

each TLP 350CV includes pass-through AAPs and a power module. A wide range of passive
AAPs are also available allowing direct connection of cables from the top and underneath
the AAPs. See

www.extron.com

for passive AAP options.

Shelf brackets are available in two-space and three-space configurations. Depending upon
the configuration, the enclosure can support up to nine AAPs. The power module takes
two (US) or three (Int’l) AAP spaces leaving seven (US) or six (Int’l) spaces for passive or
pass-through AAPs.

TIP:

The recommended way to install the cables and AAPs is to populate the shelf

brackets with pass-through and passive AAP plates outside the enclosure as
shown below, then install the populated AAP shelf assembly into the enclosure.

Assemble AAP Brackets and AAPs

Pass-through AAP's provide direct cable connection and must have the cable installed as
they are being mounted on the shelf brackets.
each AAP shelf assembly consists of a set of shelf brackets and a number of cable
pass-through and passive AAPs. Decide the location of each AAP prior to assembling the
AAP shelf.

Rear Shelf Bracket

Front Shelf Brackets

Figure 2.

Pass-through and Passive AAP Mounting

TIP:

It may be easier to cable the rear of passive AAPs prior to installing them.

TLP 350CV • Mounting the TLP 350CV

7

«
...
11
12
13
14
15
...
»

Содержание TouchLink TLP 350CV




















































Отзывы:

Нет отзывов

Похожие инструкции для TouchLink TLP 350CV

Бренд: IFM Страницы: 32

Бренд: IFM Страницы: 25

Бренд: IFM Страницы: 21

ioControl CR2050

Бренд: IFM Страницы: 126

ecomat 100 R 360

Бренд: IFM Electronic Страницы: 16

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 11

Бренд: IFM Electronic Страницы: 23

Бренд: Parkside Страницы: 86

Бренд: BendPak Страницы: 43

Бренд: RKC INSTRUMENT Страницы: 10

Бренд: Tamiya Страницы: 5

Бренд: Netro Страницы: 14

M-DUINO PLUS series

Бренд: Industrial Shields Страницы: 46

Бренд: u-blox Страницы: 157

Бренд: Airlow Страницы: 20

TOP-43 EE Series

Бренд: CAME Страницы: 2

Бренд: WattMaster Страницы: 104

magicbox aavelin

Бренд: ClearOne Страницы: 93

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды