Exmark Radius E Series Скачать руководство пользователя страница 4

Страница: 4 / 84

Contents

Introduction ........................................................... 3
Safety ..................................................................... 5

Safety Alert Symbol ......................................... 5
General Safety ................................................. 5
Safety and Instructional Decals ....................... 6

Specifications ........................................................13

Systems ..........................................................13
Dimensions....................................................16
Torque Requirements .....................................18

Product Overview .................................................18
Operation ..............................................................19

Controls .........................................................19
Before Operation ..........................................22
Operating Instructions ...................................23
During Operation Safety.................................23
After Operation..............................................31
Transporting ..................................................31

Maintenance ..........................................................35

Maintenance Safety.............................................35
Recommended Maintenance Schedule(s) ............36
Periodic Maintenance ........................................38

Engine Maintenance.......................................38
Engine Safety .................................................38
Servicing a Kawasaki

Engine ........................38

Servicing a Kohler

Engine ............................44

Servicing an Exmark Engine ...........................48
Check Battery Charge .....................................55
Check Mower Blades ......................................57
Check Safety Interlock System ........................59
Check Rollover Protections Systems (Roll

Bar) Knobs.................................................62

Check Seat Belt...............................................62
Check for Loose Hardware .............................62
Check Hydraulic Oil Level ..............................62
Check Tire Pressures ......................................62
Check Condition Of Belts...............................62
Lubricate Grease Fittings................................63
Replace Emissions Air Intake Filter (If

Applicable).................................................64

Change Hydraulic System Filter and

Fluid ..........................................................65

Check Spark Arrester (if equipped)..................65
Thread Locking Adhesives..............................66
Copper-Based Anti-seize ...............................66
Dielectric Grease............................................66

Adjustments ......................................................66

Deck Leveling ................................................66
Adjusting the Blade Slope ...............................68
Pump Drive Belt Tension................................68

Deck Belt Tension ..........................................68
Adjusting the Parking Brake............................68
Motion Control Handle Adjustment ...............69
Full Forward Tracking Adjustment..................70
Motion Control Linkage Adjustment ..............70
Electric Clutch Adjustment.............................71

Cleaning ............................................................72

Cleaning and Storing Safety.............................72
Clean Debris From Machine ...........................72
Clean Engine and Exhaust System

Area ...........................................................72

Remove Engine Shrouds and Clean

Cooling Fins...............................................72

Clean Grass Build-Up Under Deck .................72
Waste Disposal ...............................................73

Troubleshooting ....................................................74
Schematics ............................................................76
California Proposition 65 Warning

Information ...............................................79

Содержание Radius E Series





















































































Результаты поиска

Содержание Radius E Series

Отзывы:

Похожие инструкции для Radius E Series

Бренды по названию

Популярные бренды

Exmark Radius E Series, Руководство оператора

Результаты поиска

Содержание Radius E Series

Отзывы:

Похожие инструкции для Radius E Series

Бренды по названию

Популярные бренды