Exmark Radius E Series Скачать руководство пользователя страница 14

Страница: 14 / 84

Specifications

•

Deck Lift Pedal: Foot pedal that lifts deck.

•

Transport Lock: Latching position: Automatically
latches at the transport position.

Seat

•

Seat Type:

–

X-Series:

Deluxe suspension (adjustable spring
suspension) seat with high back, molded foam
flip-up armrests, and integral safety switch.

–

S-Series:

Deluxe suspension (adjustable spring
suspension) seat with high back, molded foam
flip-up armrests, and integral safety switch.

–

E-Series:

Standard seat with foam padded seat cushion
with armrests and integral safety switch.

•

Mounting:

–

X-Series:

Hinged seat frame to tilt up seat.

Adjustable fore and aft on seat tracks.

–

S- and E-Series:

Adjustable fore and aft on

seat tracks.

•

Armrests: Molded flip-up armrests.

•

Seat Safety Switch: Integrated seat switch.
Time delay seat switch eliminates rough ground
cut-outs.

Hydrostatic Ground Drive System

•

Two unitized hydrostatic transmissions:

–

X-Series:

Hydro Gear ZT3400

–

S-Series:

◊ Models with side discharge decks:

Hydro Gear ZT3100

◊ Models with rear discharge deck:

Hydro Gear ZT3400

–

E-Series:

◊ Models with 44, 48, or 52 inch decks:

Hydro Gear ZT2800

◊ Models with 60 inch deck:

Hydro Gear ZT3100

•

Hydraulic Oil Type: Exmark Premium Hydro Oil.

•

Hydraulic Oil Capacity: 77 oz (2.3 L) per side

•

Hydraulic Filter: P/N 109-3321

•

Speeds:

–

X-Series:

◊ Forward: 0-10 mph (16.1 km/hr) forward.

◊ Reverse: 0-7 mph (11.3 km/hr) reverse.

–

S-Series:

◊ Forward: 0-9 mph (14.5 km/hr) forward.

◊ Reverse: 0-6 mph (9.7 km/hr) reverse.

–

E-Series:

48 and 52

Forward

0-7 mph
(11.3 km/hr)

0-8 mph
(12.9 km/hr)

Reverse

0-4 mph
(6.4 km/hr)

0-5 mph
(8.0 km/hr)

•

Drive wheel release valves allow machine to be
moved when engine is not running.

Tires & Wheels

X-Series:

Drive

Pneumatic (Air filled)

Deck Size

48 & 52

Quantity

Tread

Super Turf

Size

24 x 9.50-12

24 x 10.5-12

Ply Rating

Pressure

13 psi (90 kPa)

S-Series:

Drive

Pneumatic (Air filled)

Deck Size

48 & 52

Quantity

Tread

Super Turf

Size

23 x 9.50-12

23 x 10.50-12

Ply Rating

Pressure

13 psi (90 kPa)

Содержание Radius E Series





















































































Результаты поиска

Содержание Radius E Series

Отзывы:

Похожие инструкции для Radius E Series

Бренды по названию

Популярные бренды

Exmark Radius E Series, Руководство оператора

Результаты поиска

Содержание Radius E Series

Отзывы:

Похожие инструкции для Radius E Series

Бренды по названию

Популярные бренды