Exmark Radius E Series Скачать руководство пользователя страница 12

Страница: 12 / 84

Safety

decal126-8151

126-8151

Read the instructions before servicing or performing
maintenance

Refer to the Operator's manual for grease instructions

Time interval

Check hydraulic oil level and refer to the Operator's
manual or further instructions

Check oil level

Check tire pressure

decal126-8383

126-8383

This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the

maximum recommended slope indicated on the decal. It is important that each operator review the slope operation

instructions in the operator’s manual and review the conditions in which the machine is being operated to determine

if the machine may be operated in the conditions that day and on that site. Changes to terrain can result in a

change in slope operation for any machine.

Warning–Read the Operator’s Manual. Do Not operate this
machine unless you are trained. Wear hearing protection.

Bodily harm hazard–Do Not carry passengers. Look
behind you when mowing in reverse.

Cutting and pinching hazard–keep hands and feet away
from moving parts; keep all guards and shields in place.

Thrown object hazard–keep bystanders away.

Ramp hazard–when loading onto a trailer, Do Not use
dual ramps; only use a singular ramp wide enough for the
machine and that has an incline less than 15 degrees;
back up the ramp (in reverse) and drive forward off the
ramp.

Tipping hazard on slopes–Do Not use on slopes near open
water; Do Not use on slopes greater than 15 degrees.

Содержание Radius E Series





















































































Результаты поиска

Содержание Radius E Series

Отзывы:

Похожие инструкции для Radius E Series

Бренды по названию

Популярные бренды

Exmark Radius E Series, Руководство оператора

Результаты поиска

Содержание Radius E Series

Отзывы:

Похожие инструкции для Radius E Series

Бренды по названию

Популярные бренды