Exmark Radius E Series Скачать руководство пользователя страница 46

Страница: 46 / 84

Maintenance

•

Crankcase Capacity: 1.9L (2 qt) when the filter
is changed.

•

Recommended Oil Type: Exmark 4-Cycle
Premium Engine Oil

– API service SJ or higher

g030595

Figure 37

Viscosity table

Note:

To prevent extensive engine wear or

damage, always maintain the proper oil level in
the crankcase. Never operate the engine with the
oil level below the “L”(LOW) mark or over the
“F” (FULL) mark on the dipstick.

Changing the Engine Oil

Service Interval: After the first 5 hours

Every 100 hours (change
it more often under a
heavy load or in high
temperatures) (Kohler
Engine).

Park the machine so that the drain side is slightly
lower than the opposite side to ensure the oil
drains completely.

Start the engine and let it run until warm. This
warms the oil so it drains better.

Disengage the blade control switch and ensure
the parking brake is engaged.

Stop the engine, remove the key, and wait for all
moving parts to stop before leaving the operating
position.

g027934

Figure 38

Note:

Torque the plug to 14 N-m (125 in-lb).

Change the engine oil filter. Apply a thin film of
clean Exmark 4-Cycle Premium Engine Oil to the
rubber gasket on the new filter.

Содержание Radius E Series





















































































Результаты поиска

Содержание Radius E Series

Отзывы:

Похожие инструкции для Radius E Series

Бренды по названию

Популярные бренды

Exmark Radius E Series, Руководство оператора

Результаты поиска

Содержание Radius E Series

Отзывы:

Похожие инструкции для Radius E Series

Бренды по названию

Популярные бренды