Exmark Radius E Series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 84

background image

Operation

the machine has to be pushed by hand, the valves
must be in the “released” position (see Figure 8).

g035062

Figure 8

1.

Front of the machine

2.

Rotate bypass release knob counterclockwise to loosen

3.

Lever position for operating the machine

4.

Pull lever in this direction to push the machine

5.

Lever position for pushing the machine

6.

Rotate bypass release knob clockwise to tighten

7.

Engine

8.

Release lever

To release the drive system (see item 1 in Figure 8),
loosen the knob by turning counterclockwise. Then
pull the release lever on the underside of machine
towards the back of the machine and retighten the
knob to hold the release lever back in the released
state. Repeat this on each side of the machine.

Release the parking brake. The machine is now able
to be pushed by hand.

To reset the drive system (see item 2 in Figure 8),
loosen the knob by turning counterclockwise. Then
push the release lever on the underside of machine
towards the front of the machine and retighten the
knob to hold the release lever in the operating state.
Repeat this on each side of the machine.

Do Not tow machine.

PTO Engagement Switch

Located on right console (see Figure 5).

Switch must be pulled out (up) to engage the blades.
Switch is pushed in to disengage the blades.

Deck Lift Pedal

Located at the right front corner of the floor pan.

Push the pedal forward with your foot to raise the
cutting deck. Allow the pedal to move rearward to
lower the cutting deck to the cut height that has been
set.

g035063

Figure 9

1.

Transport lock knob

3.

Height of cut decal

2.

Height adjustment pin

4.

Deck foot pedal

Transport Lock

Located on RH console in front of the motion
control lever (see Figure 9).

The transport latching mechanism will automatically
engage when the deck is raised to the transport
position. To release the deck from the transport
position: push the foot pedal to remove the load
from the transport latching mechanism, pull up on
the transport lock knob, and let the pedal come back
to lower the deck down to the desired cut height.

21

«
...
19
20
21
22
23
...
»

Содержание Radius E Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для Radius E Series

Бренд: Toro Страницы: 48

Бренд: White Outdoor Страницы: 4

FREEDOM Z SFZ36-17KA

Бренд: Scag Power Equipment Страницы: 69

Бренд: LawnMaster Страницы: 40

Бренд: MTD Страницы: 20

Swift S2 MJ71-190

Бренд: Major Страницы: 54

Бренд: Barbieri Страницы: 2

Бренд: Wizard Страницы: 48

Бренд: Feider Machines Страницы: 22

Бренд: Jacobsen Страницы: 106

Бренд: True-Surface Страницы: 88

Super Surfer II GSKA1948S

Бренд: Great Dane Страницы: 78

Бренд: MASSEY FERGUSON Страницы: 31

Бренд: Ego Power+ Страницы: 444

Бренд: Solo Страницы: 40

Бренд: Jacobsen Страницы: 60

Бренд: Simplicity Страницы: 4

Cruisematic 141-846H190

Бренд: White Outdoor Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды