Exmark Radius E Series Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 84

background image

Maintenance

g008804

g335566

Figure 27

5.

If the level is low, wipe off the area around the oil
fill cap, remove cap/dipstick and add oil to the
“FULL” mark on the dipstick. Exmark 4-Cycle
Premium Engine Oil is recommended; refer to
the following information for an appropriate API
rating and viscosity. Always check the level with

the dipstick before adding more oil.

Do Not

overfill.

•

Crankcase Capacity: 2.1 L (2.2 qt) when the
filter is changed.

•

Recommended Oil Type: Exmark 4-Cycle
Premium Engine Oil

– API service SF, SG, SH, SJ, or SL

g037096

Figure 28

Viscosity table

Note:

To prevent extensive engine wear or

damage, always maintain the proper oil level in the
crankcase. Never operate the engine with the oil
level below the “ADD” mark or over the “FULL”
mark on the dipstick.

Changing the Engine Oil

Service Interval: After the first 5 hours

Every 100 hours (change
it more often under a
heavy load or in high
temperatures) (Kawasaki
Engine).

1.

Park the machine so that the drain side is slightly
lower than the opposite side to ensure the oil
drains completely.

2.

Start the engine and let it run until warm. This
warms the oil so it drains better.

3.

Disengage the blade control switch and ensure
the parking brake is engaged.

41

«
...
39
40
41
42
43
...
»

Содержание Radius E Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для Radius E Series

Бренд: Land Pride Страницы: 60

Бренд: Lawn-Boy Страницы: 20

Бренд: Lawn-Boy Страницы: 16

Бренд: jobmate Страницы: 19

Z Master Professional 5000 Series

Бренд: Toro Страницы: 80

Бренд: Alamo Страницы: 99

Бренд: Swisher Страницы: 16

GRASSLAND MOWER 53 CM

Бренд: Stiga Страницы: 4

Бренд: MTD Страницы: 16

Бренд: Ryobi Страницы: 36

Бренд: Murray Страницы: 52

Бренд: Lastec Страницы: 54

Eco Wheeler GM 413.2 R

Бренд: Garten Meister Страницы: 96

Бренд: Racing Страницы: 27

Бренд: LawnMaster Страницы: 16

Бренд: EarthWise Страницы: 8

Бренд: Toyama Страницы: 44

Бренд: Toyama Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды