Exmark Radius E Series Скачать руководство пользователя | Manualshive

Страница: 6 / 84

background image

Safety

Safety and Instructional Decals

•

Keep all safety signs legible. Remove all grease,
dirt and debris from safety signs and instructional
labels.

•

Replace all worn, damaged, or missing safety
signs.

•

When replacement components are installed, be
sure that current safety signs are affixed to the
replaced components.

•

If an attachment or accessory has been installed,
make sure current safety signs are visible.

•

New safety signs may be obtained from
your authorized Exmark equipment dealer or
distributor or from Exmark Mfg. Co. Inc.

•

Safety signs may be affixed by peeling off the
backing to expose the adhesive surface. Apply
only to a clean, dry surface. Smooth to remove
any air bubbles.

•

Familiarize yourself with the following safety signs
and instruction labels. They are critical to the safe
operation of your Exmark commercial mower.

decal106-5517

106-5517

1.

Warning—do not touch the hot surface.

decal107-3069

107-3069

1.

Warning-there is no rollover protection when the roll bar
is down.

2.

To avoid injury or death from a rollover accident, keep
the roll bar in the fully raised and locked position
and wear the seat belt. Lower the roll bar only when
absolutely necessary; do not wear the seat belt when
the roll bar is down.

3.

Read the Operator’s manual; drive slowly and carefully.

6

«
...
4
5
6
7
8
...
»

Содержание Radius E Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для Radius E Series

Бренд: Yard Machines Страницы: 24

Бренд: Baroness Страницы: 19

Бренд: Baroness Страницы: 4

Бренд: Baroness Страницы: 5

Бренд: Baroness Страницы: 3

Бренд: Baroness Страницы: 142

Бренд: Baroness Страницы: 192

Бренд: Baroness Страницы: 60

Бренд: Yard-Man Страницы: 16

Бренд: jobmate Страницы: 19

Бренд: McCulloch Страницы: 100

Бренд: Weed Eater Страницы: 13

Бренд: AL-KO Страницы: 116

Бренд: Parkside Страницы: 52

Бренд: Cub Cadet Страницы: 36

Бренд: Craftsman Страницы: 22

Бренд: Craftsman Страницы: 24

Бренд: Craftsman Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды