Exmark Radius E Series Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 84

background image

Maintenance

2.

Check the gap between the center and side
electrodes.

3.

Set the gap to 0.030 inch (.76 mm).

Installing the Spark Plug

1.

Install the spark plug. Make sure that the air gap
is set correctly.

2.

Tighten the spark plug to 16 ft-lb (22 N-m).

g027735

Figure 34

3.

Push the wire onto the spark plug.

Check and Adjust Valve Clearance

Service Interval: Every 300 hours—Check

and adjust valve
clearance (Kawasaki
engine).

Refer to the Engine Owner’s Manual.

Clean Combustion Chamber

Service Interval: Every 300 hours—Clean

combustion chamber
(Kawasaki engine).

Refer to the Engine Owner’s Manual.

Clean and Lap Valve Seating Surface

Service Interval: Every 300 hours—Clean

and lap valve seating

surface (Kawasaki
engine).

Refer to the Engine Owner’s Manual.

Servicing a Kohler

®

Engine

Servicing the Air Cleaner

Service Interval: Before each use or

daily—Check the air
cleaner for dirty, loose
or damaged parts(Kohler
engine).

Every 25 hours—Service
or replace the air cleaner
precleaner (more often
under extremely dusty,
dirty conditions)(Kohler
engine).

Every 50 hours—Service
the air cleaner paper
element (more often
under extremely dusty,
dirty conditions)(Kohler
engine).

Every 100 hours—Replace
the air cleaner paper
element (more often
under extremely dusty,
dirty conditions)(Kohler
engine).

This engine is equipped with a replaceable, high
density paper air cleaner element. Check the air
cleaner daily or before starting the engine. Check for
a buildup of dirt and debris around the air cleaner
system. Keep this area clean. Also, check for loose or
damaged components. Replace all bent or damaged
air cleaner components.

Note:

Operating the engine with loose or damaged

air cleaner components could allow unfiltered air into
the engine, causing premature wear and failure.

Note:

Service the air cleaner more often under

extremely dusty, dirty conditions.

1.

Park the machine on a level surface, disengage the
blade control switch, move the motion control
levers to the brake position, stop the engine,
remove the key, and wait until all moving parts
stop before leaving the operating position.

44

«
...
42
43
44
45
46
...
»

Содержание Radius E Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для Radius E Series

Бренд: Walker Страницы: 76

Бренд: PAPILLON Страницы: 27

Бренд: Yard-Man Страницы: 16

Бренд: Yard-Man Страницы: 11

Silver Series 10270

Бренд: Lawn-Boy Страницы: 29

Бренд: Nakayama Страницы: 19

Бренд: Worx Страницы: 64

Бренд: Walker Страницы: 84

Бренд: GGP ITALY SPA Страницы: 72

Бренд: LawnMaster Страницы: 81

Бренд: MASSEY FERGUSON Страницы: 31

REVOLT BRV36FX691

Бренд: Bad Boy Страницы: 36

Бренд: Exmark Страницы: 4

Бренд: Husqvarna Страницы: 3

Бренд: Husqvarna Страницы: 56

Бренд: Yard-Man Страницы: 20

Бренд: Jonsered Страницы: 120

Бренд: Craftsman Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды