EWIKON L2X Скачать руководство пользователя страница 68

Страница: 68 / 88

HPS-III-Heißkanalsystem_Instandhaltung-Düsenspitzenwechsel_BA_V-2-0_EN

7.4.7 Installation of one-piece nozzle tips

1. The contour plate must be deinstalled.

2. Apply a thin and even coat of engineer's blue (see chap-

ter „5.3.1 Tools and operating materials“) to the contact

surface of the cold nozzle tip (pos. 1.9 / surface T).

3. Apply high temperature installation paste (see chapter

„5.3.1 Tools and operating materials“) to the thread of

the nozzle tip (pos. 1.9 / surface G).

Attention: Surfaces where engineer's blue is applied

must not get in contact with the installation paste be-

cause otherwise the transfer of the blue is falsified.

4. Screw the nozzle tip (pos. 1.9) into the pressure tube

(pos. 1.1) and tighten with the matching tightening

torque. See chapter „9.3 Tightening torques for tip

inserts“.

Important: Before installing a valve gate nozzle tip

the valve pin must be moved to position „open“.

5. Unscrew and deinstall the nozzle tip again and check

the transfer of the blue. The surface T between nozzle

tip (pos. 1.9) and pressure tube (pos. 1.1) must show an

even ring-shaped transfer of the blue.

6. Clean all surfaces from engineer's blue.

7. Heat up nozzle to 220 °C (428 °F).

8. Apply high temperature installation paste to the thread

of the nozzle tip (surface G) again. Install nozzle tip

(pos. 1.9) again as described under 4.

9. Let the nozzle cool down before carrying out further work

steps.

Picture 46: Installation of nozzle tip

z352-14

Picture 47: Tightening of nozzle tip

z352-15

Maintenance

When nozzle tips of HPS III nozzles or HPS III-SXE single tips are
exchanged while the nozzle is installed in the mould a lock against
rotation (dowel pin, pos 1.10) must be installed.

NOTE!

Sharp edges and heavy components

•

Cut injuries to body and extremities, mainly to the hands.

•

Crushing of fingers or hand.

Hot surfaces

Burns to the body caused by hot surfaces.

WARNING!

Содержание L2X

























































































Результаты поиска

Содержание L2X

Отзывы:

Похожие инструкции для L2X

Бренды по названию

Популярные бренды

EWIKON L2X, Руководство по эксплуатации

Результаты поиска

Содержание L2X

Отзывы:

Похожие инструкции для L2X

Бренды по названию

Популярные бренды