EWIKON L2X Скачать руководство пользователя страница 29

Страница: 29 / 88

HPS-III-Heißkanalsystem_Vorspann_BA_V-2-0_EN

Installation

5.3 Technical Requirements

Specific connections and hoses are used for supply lines (hydraulic, cooling water).

5.3.1 Tools and operating materials

Tool

Use

Version

EWIKON

item no.

Abrasive paper /

non-woven web

Exchange of nozzle heater

Various

Allen key

For hexagon socket head cap screw

according to DIN EN ISO 4062

Depending on system and components.

For wrench sizes see chapter

„9. Tightening torques“.

Allen key,

extension for allen key

Deinstallation of HPS III-MH

clamping covers

Deinstallation of a screw bush

Exchange of seal kits of drive units

Deinstallation / exchange of valve pins

Various

Allen key with hole

Exchange of seal kits of drive units

Various

17919

19182

Blowtorch / small burner

Exchange of thermocouples

Cable markers

(cable numbers)

Marking of electrical connections

Cable tie PA4.6

Fixation of cables, temperature sensors

and shrink hoses

100 mm

150 mm

13590

13591

Centering aid

Assemby of L2X systems

Ø 10 mm/Ø 16 mm

19103/19104

Chain slings

(with metal tag)

Lifting and moving of hot halves,

systems (L2X) and plate assemblies

According to DIN EN 1677

(metal tag according to DIN 685)

Clamping device

Maintenance of HPS III-MHR nozzles

Cordless screwdriver

Exchange of valve pin seal of valve gate

systems

Copper drift

Exchange of HPS III-MH thermocouples

Crimping tool

Attachment of cable pins to cables

Depth gauge

Control of check dimensions

Disassembly sleeve

Deinstallation / exchange of valve pins

Various

See HPS III-

NV catalogue

Drift punch

Installation of dowel pins

Engineers hammer

Maintenance work

Fabric tube

Protection of cables

Ø 6 mm

13479

Hexagon socket bit

Installation / deinstallation of

HPS III-MH clamping covers.

Installation with torque wrench only

Various

Hexagon socket

wrench insert

Installation / deinstallation of

tip inserts. Installation with torque

wrench only

Closed

Impact wrench

Deinstallation of a screw bush

1/2 inch adapter

Installation wrench

Installation of drive units

Various

See HPS III-

NV catalogue

Installation wrench,

extension for installation

wrench

for L2X nozzles

Various

See L2X

catalogue

Insulation stripping pliers

Stripping of cables

Key with pilot

For hexagon socket screws

according to DIN 6912

Key according to DIN 6911

Levering and striking tool

Disassembly of hot runner nozzles

Soft, preferably massive brass rod with

tapered end, various sizes

Lifting beam

Lifting and moving of hot halves,

systems (L2X) and plate assemblies

For specifications see manufacturer

Содержание L2X

























































































Результаты поиска

Содержание L2X

Отзывы:

Похожие инструкции для L2X

Бренды по названию

Популярные бренды

EWIKON L2X, Руководство по эксплуатации

Результаты поиска

Содержание L2X

Отзывы:

Похожие инструкции для L2X

Бренды по названию

Популярные бренды