EWIKON L2X Скачать руководство пользователя страница 37

Страница: 37 / 88

HPS-III-L2X-Heißkanalsystem_Montage_BA_V-2-0_EN

Installation of L2X Drop-in hot runner systems

5.5 Installation of L2X Drop-in hot runner systems

Picture 23: General layout of a L2X system

z347-01

Pos. 1 Manifold

Pos. 2 L2X nozzle

Pos. 5 Sprue bush

Pos. 6 Locating ring

Pos. 10 Drive unit on manifold (screwed-on) (version 1)

(for valve gate systems)

Pos. 10 Drive unit on manifold (screwed-on) (version 2)

(for valve gate systems)

Pos. 13 Screw connection for manifold

Pos. 14 Centring aid

Pos. 50 Insulating plate

Pos. 51 Clamping plate

Pos. 53 Nozzle retainer frame plate

Pos. 56 Contour plate

The positions 1 - 2 are delivered as a completely

assembled and wired system including electrical

connector box. In addition the valve gate version

includes the complete piping for the drive units

as well as a connector block for the supply lines.

Connector block for valve gate supply lines

Electrical connector box

Read operating manual

In the installation process described in the following hazards for the
personal health are listed explicitly.

Furthermore, during installation the warning, safety and installation
notes for installation of EWIKON hot runner systems and compo-

nents as specified in chapter „5.2 General safety instructions“ must

be followed!

NOTE!

Dimensional check

Before installation the installation dimensions as listed in chapter
„5.4 Checks before installation“ must be checked and compared with
the values provided with the installation drawing.

Use approved standard parts only

Only standard parts which are approved for use in EWIKON hot
runner systems must be used. See chapter „5.3 Technical Requi-
rements“.

NOTE!

Содержание L2X

























































































Результаты поиска

Содержание L2X

Отзывы:

Похожие инструкции для L2X

Бренды по названию

Популярные бренды

EWIKON L2X, Руководство по эксплуатации

Результаты поиска

Содержание L2X

Отзывы:

Похожие инструкции для L2X

Бренды по названию

Популярные бренды