EWIKON L2X Скачать руководство пользователя страница 32

Страница: 32 / 88

HPS-III-Heißkanalsystem_Vorspann_BA_V-2-0_EN

Installation

NOTE!

Only use approved standard parts

Damage to the HPS III hot runner system and/or components of the surrounding injection mould.

•

Only standard parts which are approved for operation in EWIKON hot runner systems must be used.

The following standard parts with the associated standards are approved for EWIKON hot runner systems. Particularly for

screws the associated strength classes (see chapter 5.5 Assembly of the system / the components) and tightening torques

(compare chapter „9. Tightening torques“) must be adhered to.

Standard part

Valid standard

Invalid/old standard

Hexagon socket head cap screw

DIN EN ISO 4762 (ISO 4762)

DIN 912

Hexagon socket head cap screw - low

head, with pilot recess

DIN 6912

Countersunk screw

DIN EN ISO 10642 (ISO 10642)

DIN 7991

Parallel pin

DIN EN ISO 2338 (ISO 2338)

DIN 7

Parallel pin with internal thread

DIN EN ISO 8735 (ISO 8735)

DIN 7979

Flat washer

DIN EN ISO 7089 (ISO 7089)

DIN 125-1 (DIN 125)

Flat washer

DIN EN ISO 7092 (ISO 7092)

DIN 453-1 und DIN 433-2

Feather key

DIN EN ISO 773 (ISO 773)

Lock ring

DIN 471

Split pin

DIN EN ISO 8752 (ISO 8752)

DIN 1481

Chart 10: Approved standard parts for EWIKON hot runner systems

5.3.2 Standard parts

Содержание L2X

























































































Результаты поиска

Содержание L2X

Отзывы:

Похожие инструкции для L2X

Бренды по названию

Популярные бренды

EWIKON L2X, Руководство по эксплуатации

Результаты поиска

Содержание L2X

Отзывы:

Похожие инструкции для L2X

Бренды по названию

Популярные бренды