EWIKON L2X Скачать руководство пользователя страница 66

Страница: 66 / 88

HPS-III-Heißkanalsystem_Instandhaltung-Düsenspitzenwechsel_BA_V-2-0_EN

Picture 42: Clamping of a deinstalled HPS III nozzle in a vice

z352-03

Exchange of nozzle tips outside the mould

To exchange a nozzle tip outside the mould a vice is requi-

red. Protective jaws (pos. 70, preferrably made from alumini-

um), must be used to avoid damage to the nozzle.

The nozzle must always be clamped at the pressure tube

(pos. 1.1) . A HPS III-SXE single tip is clamped at the nozzle

body (see picturePicture 42).

7.4.4 Exchange of nozzle tips with nozzle installed in the mould

Standard installation

An exchange of nozzle tips must only be carried out when the nozzle is locked against rotation by a dowel pin in the mould.

Otherwise the heater or the thermocouple may be teared off.

Attention:

When HPS III-S nozzles with flow channel Ø 3 and 4.5 mm for standard installation are used the installation of a

dowel pin is not possible. Thus, the nozzle tips can not be exchanged with the nozzle installed in the mould.

Furthermore, a tip exchange inside the mould for HPS III-SXE single tips is only possible when the nozzle is fixed in the

clamping plate with the locating ring. Otherwise it may fall out and be damaged.

Front installation

A nozzle tip exchange for nozzles for front installation which are screw connected to the mould is possible without a lock

against rotation.

Clamping of nozzle in a vice

The nozzle must be clamped in the indicated areas only to avoid
damage.

If it is necessary to heat up the nozzle to deinstall the nozzle tip the
vice must be grounded.

CAUTION!

7.4.5 Exchange of nozzle tips outside the mould

Clamping of nozzle in a vice

Maintenance

Содержание L2X

























































































Результаты поиска

Содержание L2X

Отзывы:

Похожие инструкции для L2X

Бренды по названию

Популярные бренды

EWIKON L2X, Руководство по эксплуатации

Результаты поиска

Содержание L2X

Отзывы:

Похожие инструкции для L2X

Бренды по названию

Популярные бренды