EWIKON L2X Скачать руководство пользователя страница 15

Страница: 15 / 88

HPS-III-Heißkanalsystem_Vorspann_BA_V-2-0_EN

Safety instructions

The technical service provided verbally, in writing or on the basis of tests represents our best knowledge but is not binding

and does not release you from carrying out additional tests on the products supplied by us regarding their suitability for the

intended use.

The use of the products is beyond our control. Therefore, it is your own responsibility to ensure that the products meet your

specific requirements. Nevertheless, should an issue of liability arise, all damage shall be limited to the value of the products

supplied by EWIKON and used by you.

We guarantee the perfect quality of our products in accordance with our general terms and conditions of sale and payment

as well as the extended warranty conditions.

These are available on our homepage

www.ewikon.com

The statutory provisions prevailing at the time of conclusion of the contract shall apply.

We reserve the right of technical alterations to develop our products and enhance their performance properties.

2.10 Warranty terms

For warranty conditions of cold and hot runner systems and components please refer to the terms and conditions of

EWIKON.

2.11 Standards and directives

EWIKON hot runner systems conform to the following European directives:

•

Machinery Directive 2006/42/EC

•

Low Voltage Directive 2014/35/EU

•

EN ISO 12100:2010 Safety of machinery -

General principles for design - Risk assessment and risk reduction

•

EN 60204-1:2007-06 Safety of machinery -

Electrical equipment of machines - Part 1: General requirements

Содержание L2X

























































































Результаты поиска

Содержание L2X

Отзывы:

Похожие инструкции для L2X

Бренды по названию

Популярные бренды

EWIKON L2X, Руководство по эксплуатации

Результаты поиска

Содержание L2X

Отзывы:

Похожие инструкции для L2X

Бренды по названию

Популярные бренды