Ever SINLINE PRO 10000 Скачать руководство пользователя | Manualshive

Страница: 29 / 42

background image

Instruction manual for SINLINE PRO 10000 series power supply units

2010/08/24

www.ever.eu

29

OPERATING MODES OF THE POWER SUPPLY UNIT

Figure 5: Graph presenting the operation modes of the power supply unit

UNKNOWN mode

An intermediate state that occurs when the power supply unit is started up

following energisation.

INIT (INITIALISATION) mode

An intermediate state that occurs following initiation of the hardware platform

by means of start-up values or during a return from EMERGENCY mode.

NORMAL mode (MAINS OPERATION)

In for the power supply unit to be in NORMAL mode, it must by logically switch

on (from the user interface). In addition, the input primary power line must satisfy the
mains correctness criteria (correct value of voltage and frequency). The unit then
supplies power to the outputs from the abovementioned line, with the AVR system
making the necessary corrections. In this mode, the batteries are topped up.

«
...
27
28
29
30
31
...
»

Содержание SINLINE PRO 10000











































Отзывы:

Нет отзывов

Похожие инструкции для SINLINE PRO 10000

Бренд: Datavideo Страницы: 8

Бренд: National Flooring Equipment Страницы: 28

750-626/xxx-xxx

Бренд: WAGO Страницы: 46

Бренд: Total Страницы: 11

Бренд: VONROC Страницы: 84

Бренд: Toolson Страницы: 136

Бренд: Whelen Engineering Company Страницы: 2

Бренд: FASANO TOOLS Страницы: 8

Бренд: Kett Страницы: 6

Бренд: EVGA Страницы: 10

Бренд: Tyco Страницы: 11

Бренд: Crommelins Страницы: 12

Бренд: BJLive Страницы: 2

Бренд: PowerGrip Страницы: 18

Бренд: Cembre Страницы: 20

Бренд: Huck Страницы: 26

Бренд: Greenlee Страницы: 20

Бренд: ODA Страницы: 89

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды