EVA MAJOLICA LINE, Инструкция по эксплуатации

Страница: 68 / 90

67
12. N100 MICRONOVA ELECTRONICS WITH 6-BUTTON LED DISPLAY
12.3.2 Pellet feeding
The pellet feeding phase starts after approx. 1 minute: the message "Carica pellet" scrolls on the display and the ON/OFF LED starts
flashing. During the first stage the Auger tube feeds the pellets to the burn pot during a period of time set by PR40 parameter (Auger
tube LED on), the exhaust blower speed is set by PR42 parameter and the ignition plug is still on (ignition plug LED on). During the
second stage, once the period of time set by PR40 parameter has elapsed, the Auger tube switches off (Auger tube LED off) during a
period of time set by PR4 1 parameter, while the exhaust blower speed remains as in the previous status. The ignition plug is still on.
In case of ignition failure at the end of this phase, the Auger tube switches back and remains on during the period of time set by
PR04 parameter, the exhaust blower speed is set by PR1 6 parameter and the ignition plug is still on.
12.3.3 Fire on
Once fume temperature has reached and exceeded PR13 parameter value, the stove goes into the ignition mode: the message "Fuoco
presente" appears on the display and the ON/OFF LED starts flashing.
During this phase the temperature remains stable for a period of time preset by PR02 parameter.
The exhaust blower speed is set by PR17 parameter, the Auger tube remains on for a period of time set by PR05 parameter (Auger tube
LED flashing) and the ignition plug is off (ignition plug LED off).
Any problem during this phase will cause the control board to stop and the stove to go into error state.
12.3.4 Working mode
Once fume temperature has reached and exceeded PR13 parameter value, maintaining it for the period of time set by PR02
parameter, the stove enters the normal working mode. The message "Lavoro" appears on the display and the ON/OFF LED is on.
Hold P5, P6 buttons down to set the heat output and press P1,P2 buttons to set the room temperature.
If fume temperature reaches the threshold set by PR1 5 parameter, the air exchanger fan will switch on (as the exchanger LED). During
this phase, after a period of time set by PR03 parameter, the stove cleans the burn pot. The message "Pul-braciere" scrolls on the display,
the Auger tube is on (as the relevant LED) at a speed set by PR09 parameter and the exhaust blower at a speed set by PR08 parameter.
Once the period of time set by PR12 parameter has elapsed, the stove goes back to the working mode.
12.3.5 Changing set heat output
During stove normal operation (“Lavoro” – working mode), the heat output can be changed by using P5, P6 buttons (Heat output setting
LED on). Press P6 button again to increase the heat output and P5 button to decrease it. The display will show the set heat output. Do
not press any button for 5 seconds or press P4 button to exit the setting mode.
12.3.6 Changing set room temperature
Press P1, P2 buttons to change the set room temperature. The display shows the set room temperature (SET temperature value). Press
P1 and P2 buttons to decrease or increase, respectively, the temperature value. The value is saved after approx. 5 seconds and the
display goes back to normal. Otherwise, press P4 to exit. “Man” too, so the stove works in manual way at a fix power. Or “T-E”, to chose
when an external thermostat has been connected.
12.3.7 Room temperature reaches set value (SET temperature value)
Once the set room temperature value has been reached, the stove heat output is automatically set to the minimum value. During this
phase the display shows the message "Modula". If room temperature falls below the set value (Set temperature value), the stove will
go back to the "Lavoro" mode and to the previously set heat output (Set heat output value). When an external thermostat is connected
and it has been set the room temperature in “T-E” , if the thermostat is open , it moves to MODULATION Mode, while if it closed , it
moves back to the set power.
12.3.8 Stand-by
When enabled in the menu, the Stand-by function allows the stove to be switched off after complying with the following conditions. It is
enabled if the room temperature exceeds the relevant set value (Set room temperature value) during the period of time set by PR44
parameter to which PR43 parameter must be added. The message "Go-standby" appears on the display followed by the minutes left.
At the end of the period of time set by PR44 parameter the message "Attesa raffredda" will appear on the display. During this phase
the Auger tube is off (Auger tube LED off), the exchanger switches off once the threshold set by PR1 5 parameter has been reached and
the ON/OFF LED flashes.
When fume temperature reaches the threshold set by PR13 parameter, the stove goes into the Stand-by mode and the message
"Stop eco temp good" scrolls on the display. The Auger tube (Auger tube LED off), the exchanger (exchanger LED off) and the
exhaust blower are off.
12.3.9 Spegnimento della stufa
Hold P4 button down to switch off the stove. The display shows the message "Pul-Finale”. The Auger tube motor switches off (Auger
tube LED off), the exhaust blower speed is set by PR08 parameter and the ON/OFF LED flashes. The exchanger blower remains on
(exchanger LED on) until the fume temperature falls below the value set by PR1 5 parameter. If, at the end of the period of time set by
PR39 parameter, the fume temperature remains below the threshold set by PR1 0 parameter, the stove will switch off and the message
"Off" appears on the display.