ES&S DS850 Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 199

background image

Chapter 6: Election Day Tasks

101

EVS5200_DOC_SOP_DS850

Software Version 2.10

Published: February 26, 2014

Sorting Off

The DS850 scanner diverts ballots to the following bin:



All the ballot conditions except the following conditions will be diverted to the
bottom bin for processing.

•

Invalid ID

•

Unreadable

Invalid ID and Unreadable ballots will not be processed and diverted to the top bin.

If the Sorting button is set to OFF the following will occur:

•

Write-Ins, Overvote, Undervotes, Blank, Unclear Marks and Crossover ballots are
processed and diverted to the bottom bin.

•

Invalid ID ballots are NOT processed and divert to the middle bin, if middle bin

is set to Not processed and if the Invalid ID condition is configure to go to the

middle bin.

•

Unreadable ballots that cannot be read will divert to the top bin

If the Sort Option is set to Disabled, the Sorting on/off button is not displayed on the
scan ballots screens. However, sorting is performed as if the Sort Option was set to
Enabled and the Sorting on/off button was set to On.

Not Processed Ballot Report

The DS850 can generate a “Not Processed Ballots Report” for the ballots that were
out-stacked to the Top Bin.

Note:

The saved cast vote records for ballots that are diverted to the Not Processed bin are

marked for exclusion from the collection process.

When loaded, the Election Definition establishes the sort settings for the election. An Operator
may change these settings via the series of Sort Settings screens, previously described in this
manual. Accordingly, the current, existing sort settings may not be those established by the
Election Definition.)

«
...
105
106
107
108
109
...
»

Содержание DS850








































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DS850

Бренд: ABB Страницы: 50

ACS880-01 Series

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 36

Бренд: ICP DAS USA Страницы: 8

Бренд: Johnson Controls Страницы: 11

Inocoat Inocenter

Бренд: Sames Страницы: 58

Perma-Tork HB6-1

Бренд: Magpowr Страницы: 4

Бренд: CNC Страницы: 21

Бренд: Skymsen Страницы: 24

Бренд: RIB Страницы: 4

Бренд: ITI Страницы: 42

Бренд: Labelmate Страницы: 8

Бренд: Genmitsu Страницы: 104

Бренд: Quick Страницы: 46

Бренд: SMC Networks Страницы: 32

Бренд: Raypa Страницы: 22

BNI IOL-719-002-Z012

Бренд: Balluff Страницы: 106

Бренд: York Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды