Epson S5U1C17001C, Руководство пользователя

Страница: 720 / 742

Reference
Debugger gdb (7) Development Tools
Status and Error Messages
Error messages
Invalid parameter file, The address range set in the parameter file is invalid,
start address > end address(
#
:
file
). as the number used as the start address is greater
than that used as the end address.
It has not connected with a target. The ICD cannot be connected to the target.
It is not c17 architecture ELF file. The file specified with the
file
command is not an
elf format file supported in S5U1C17001C.
Load end address max(0x # ) overflow. The end address of the program to be written to flash
memory exceeds the upper limit (0xffffff).
Load max address(0x # ) overflow. The addresses to be loaded exceed the maximum
value.
Load motorola file format error.( file ) The specified Motorola file contains a format error.
Load size limit(0x
#
) overflow. The size of the specified file exceeds the upper limit.
¥ Flash write/erase program
8K bytes - 1 byte (0x1fff)
¥ Write data for flash memory
3M bytes - 1 byte (0x2fffff)
¥ Firmware
8M bytes - 1 byte (0x7fffff)
Load start address max(0x # ) overflow. The start address of the program to be written to
flash memory exceeds the upper limit (0xffffff).
Profiler Window is already opened. A profiler window is open.
Receiving message is inaccurate. A message exceeding the maximum size was
received during communication with the ICD.
Specification is required in the device for There is an insufficient number of device names from
connecting.
which to select the ICD in the
target
command.
Target down. A communication error has occurred between the
ICD and the target.
There is no argument given to this The system failed to disconnect the target.
command.
Timeout error
#
(ICD17 -> host). In communication with the ICD, a receive operation
timed out during the wait for data from the ICD.
Too much event(
#
). The number of events specified with the
c17 int_
load
(event file read) command exceeds the upper
limit (256).
Transmitting failure( # ). NAK was received from the ICD during
communication with the ICD.
USB communication error(host->ICD17). The system failed in USB transmission to the ICD.
USB communication error(ICD17->host). The system failed in USB receiving from ICD.
Write entry address max(0x
# ) overflow. The address of the flash write routine exceeds the
upper limit (0xffffff).
Error messages
Cannot display clock counter. The execution counter value cannot be displayed when
Now Timer break mode is on. the lapse of time break is enabled. Disable the lapse
Please timer break mode off. of time break before execution times can be measured.
Cannot display clock counter. The execution counter value cannot be displayed if
Time measurement should use continue the
continue
or
until
command has not been
or until command. executed.
Cannot measure clock timer. The program execution time cannot be measured as
it is too short.
Cannot open file( file ). The system cannot open the file.
Cannot open ICD17 usb driver. The system failed to open the USB driver.
Cannot set hard pc break any more. The number of hardware PC breakpoints set exceeds
the limit (1).
Cannot set soft pc break any more. The number of software PC breakpoints set exceeds
the limit (200).
Cannot set timer. Cannot set a lapse of time break as the specified
Timer Conditions: 1<=Timer<=300000 time exceeds the valid range.
Cannot write file. The system cannot write to the file.
Clock timer overflow. The clock measurement timer has overflowed.
Communication error(bcc). A BCC error was found in the messages received
from the ICD.
Communication system error( # ). The connection was unexpectedly terminated during
communication with the ICD.
Copy end address max(0x#) overflow. The end address of the source to be copied exceeds
the upper limit (0xffffff).
Copy start address max(0x#) overflow. The start address of the source to be copied exceeds
the upper limit (0xffffff).
Coverage Window is already opened. A coverage window is open.
CPU is running. Cannot accept a command while the CPU is running.
Erase entry address max(0x#) overflow. The flash erase routine address exceeds the upper
limit (0xffffff).
Flash memory end address max(0x#) The flash memory end address exceeds the upper
overflow. limit (0xffffff).
Flash memory start address max(0x#) The flash memory start address exceeds the upper
overflow. limit (0xffffff).
ICD17 is busy( # ). The ICD side is busy.
Initialization error of ICD17. The system failed to initialize the target.
Invalid ID error(0x # ). The
gdb
has transmit an invalid ID number.
(Internal error)
Invalid parameter file( # : file ). The parameter file contains an error.