Epson S5U1C17001C, Руководство пользователя

Страница: 614 / 742

S5U1C17001C ManUal
EPSOn
10-163
(C COMPilEr PaCkagE fOr S1C17 faMily) (Ver. 1.5.0)
10 DEBUggEr
10
Debugger
Message Description
Cannot set timer.
Timer Conditions: 1<=Timer<=300000 Cannot set a lapse of time break as the specified time exceeds
the valid range.
Cannot write file. Cannot write to the file.
Clock timer overflow. The counter overflows during clock measurement.
Communication error(bcc). A BCC error occurred in the message received from ICD.
Communication system error(
#
). Connection was severed while communicating with ICD.
Copy end address max(0x # ) overflow. The end address of the source to be copied exceeds the upper
limit (0xffffff).
Copy start address max(0x # ) overflow. The start address of the source to be copied exceeds the upper
limit (0xffffff).
Coverage Window is already opened. A coverage window is open.
CPU is running. Cannot accept a command while the CPU is running.
Erase entry address max(0x # ) overflow. The flash erase routine address exceeds the upper limit (0xffffff).
Flash memory end address max(0x # ) overflow. The flash memory end address exceeds the upper limit (0xffffff).
Flash memory start address max(0x # ) overflow. The flash memory start address exceeds the upper limit (0xffffff).
ICD17 is busy( # ). ICD is in a busy state.
Illegal instruction. An attempt was made to execute an undefined instruction in
simulator mode.
Initialization error of ICD17. Failed to initialize the target.
Invalid ID error(0x # ). The gdb has transmit an invalid ID number. (Internal error)
Invalid parameter file( # : file ). The parameter file contains an error.
Invalid parameter file, start address > end
address(
# : file ).
The start and end addresses set in the parameter file are invalid
because the former is greater than the latter.
It has not connected with a target. The ICD and target cannot be connected.
It is not c17 architecture ELF file. The file specified with the
file
command is not an elf format
file supported in S5U1C17001C.
Load end address max(0x # ) overflow. The end address of the program to be written to flash memory
exceeds the upper limit (0xffffff).
Load max address(0x # ) overflow. The address to be loaded exceeds the maximum value.
Load motorola file format error.( file ) The specified Motorola file contains a format error.
Load size limit(0x # ) overflow. The size of the specified file exceeds the upper limit.
• Flash write/erase program 8K bytes - 1 byte (0x1fff)
• Write data for flash memory 3M bytes - 1 byte (0x2fffff)
• Firmware 8M bytes - 1 byte (0x7fffff)
Load start address max(0x # ) overflow. The start address of the program to be written to flash memory
exceeds the upper limit (0xffffff).
Profiler Window is already opened. A profiler window is open.
Receiving message is inaccurate. A message exceeding the maximum size was received during
communication with ICD.
Specification is required in the device for connecting. The device name for ICD selection in the
target
command
must be specified correctly.
Target down. A communication error has occurred between the ICD and the
target.
There is no argument given to this command. Failed to disconnect the target.
Timeout error # (ICD17 -> host). Wait for reception from ICD timed-out during communication with
ICD.
Too much event( # ). The number of events specified with the
c17 int_load
(event
file read) command exceeds the upper limit (256).
Transmitting failure( # ). NAK was received from ICD during communication with ICD.
USB communication error(host->ICD17). Failed in USB transmission to ICD.
USB communication error(ICD17->host). Failed in USB receiving from ICD.
Write entry address max(0x # ) overflow. The address of the flash write routine exceeds the upper limit
(0xffffff).
ICD denotes the ICD Mini (S5U1C17001H) or ICD board.