Epson EMP-7300 Скачать руководство пользователя

Страница: 110 / 110

4-13

REV.A

Figure4- 12

Others

Start

Noise problem?

Suspect following defects.

−

Exhaust fan, cooling fan and inhale fan on the power supply unit.

−

Power supply unit (Vibration noise from pulse transformer)

Suspect following defects.

−

Thermister (LV/PBS/Lamp)

−

Exhaust fan, Cooling fan

−

Air filter frame (Dirt condition)

Suspect following defects.

−

Optical engine (May cause with dirt condition on the light guide unit, projection
lens unit and light valve on the optical head unit.)

Suspect following defects.

−

AC input(Include power line transit or distortion)

−

Power supply unit

−

CD10MA board

−

Cable connection (fail to make condition.)

Overheat problem?

Image display problem?

Low reproduced problem?

YES

Содержание EMP-7300















































































































Результаты поиска

Содержание EMP-7300

Отзывы:

Похожие инструкции для EMP-7300

Бренды по названию

Популярные бренды

Epson EMP-7300, Руководство по обслуживанию

Результаты поиска

Содержание EMP-7300

Отзывы:

Похожие инструкции для EMP-7300

Бренды по названию

Популярные бренды