manualshive.com logo in svg

Epson EMP-7300, Руководство по обслуживанию

Поделиться
Скачать
Epson EMP-7300 Скачать руководство пользователя страница 106

4-9

REV.A

Figure4- 8

Audio output

Start

Does audio device is plugged
to the Audio interface?

Connect the audio cable to
the above interface.

Connect the audio cable to
the Audio In 1 or 2 interface.

YES

YES

YES

YES

YES

YES

Does volume control works?

Replace CD10AU board.

Does internal speaker R/L

output the sound?

Connect the external speaker

to the Audio out.

Does external speaker output

the sound?

Replace CD10AU board.

Replace CD10AU board.

Replace CD10MA board.

Does volume control works?

Replace CD10MA board.

Does Mute button works?

Does Mute button works?

Re-connect the CN402 on the

CD10MA board.

Does internal speaker R/L

output the sound?

Replace speaker R/L.

Does internal speaker R/L

output the sound?

Replace CD10AU board.

Does internal speaker R/L

output the sound?

Replace CD10MA board.

YES

NO

NO

NO

NO

NO

NO

NO

YES

NO

YES

NO

YES

NO

A

A

Go to Switch panel.

Does internal speaker R/L

output the sound?

Replace CD10AJ board.

Содержание EMP-7300















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды