Epson EMP-7300 Скачать руководство пользователя страница 59

Страница: 59 / 110

2-30

REV.A

2.15 SENSOR / SWITCH

For user’s safety and safety operation of this projector (for prevention from
malfunction), the following devices listed the table *-* are installed in it.

Table2- 5 Sensor/switch

Name

Location/Type

Function/Use

Interlock switch

Push-switch on the power supply
unit

Power off, in opening the lamp
cover. (Power on is disabled.)

Safety switch

Thermal switch on the lamp outer
housing

Overheat protection for light
source lamp area. Power is shut,
temperature exceeds limitation.

Lamp house thermistor

On the lamp outer housing
(Thermistor)

Overheat protection for light
source lamp area. Power off,
temperature exceeds limitation

LV thermistor

On the prism duct (Thermistor)

Overheat protection for light bulb.
Power off, temperature exceeds
limitation.

Front temperature thermistor

On the side of the power supply
unit (Thermistor)

Overheat protection for power
supply unit. Power is shut,
temperature exceeds limitation.

Содержание EMP-7300















































































































Результаты поиска

Содержание EMP-7300

Отзывы:

Бренды по названию

Популярные бренды

Epson EMP-7300, Руководство по обслуживанию

Результаты поиска

Содержание EMP-7300

Отзывы:

Бренды по названию

Популярные бренды