Emerson Liebert NXL 250 kVA Скачать руководство пользователя

Страница: 40 / 112

Operation

Liebert

NXL

™

2.15.2 Startup—N+1 System

The following instructions will start an individual UPS module. Repeat these steps for all the UPS

units in the system that will be started.
This section lists typical step-by-step instructions. The touchscreen will list all steps required for the

process, based on the unit’s condition and other factors.

NOTICE

Risk of improper startup. May cause equipment damage.
These steps should be performed after the SCC startup has been initialized.

NOTICE

Risk of equipment damage. If an abnormal situation occurs during this startup procedure, open

the input circuit breaker and investigate the problem. Call Liebert Services if help is needed.

1. Before applying power to the UPS modules, determine the position of the following circuit

breakers and switches:

•

Input Circuit Breaker (CB1)

—Verify that this breaker on the front of the UPS cabinet

(

Figure 6

) is in the open position.

•

Module Battery Disconnect (MBD)

—Verify that this external breaker is open or tripped. If

DC source cabinets are used, verify that breakers on all the cabinets are open.

•

Output Circuit Breaker (CB2)

—This motorized circuit breaker (

Figure 6

) should be open.

•

Module Output Breaker (MOB)

Optional—This circuit breaker should be open. This breaker is

external to UPS, possibly in the paralleling gear.

2. Close the Rectifier Feed Breaker (RFB). This breaker is external to UPS, possibly in the

paralleling gear. The display touchscreen should start.

3. Close the MOB breaker, if present on the system.
4. Press the “Start-Up,” then the “Manual Start” menu button (see

Figure 37

). The “Close CB1”

message will appear.

5. Close CB1 (see

Figure 6

). The “Press OK to Issue Rectifier On Command” message will appear.

6. Press “OK.” This will start the UPS’ rectifier. The message “Press OK to Issue Inverter On

Command” will appear.

7. Press “OK.” The rectifier will be On and the Inverter will be on standby. The message “Press OK

to Issue MBD Enable Command” will appear.

8. Press “OK.”

WARNING

Risk of electrical shock and high short circuit current. Can cause equipment damage, personal

injury and death.
If the UPS has been shut down for maintenance, verify that all of the UPS system doors are

closed and latched. All test equipment must be removed from the system. All electrical

connections must be secure

WARNING

Risk of electrical shock. Can cause equipment damage, personal injury and death.
The following procedure may provide power (with DC source available) to the critical load

distribution system. Verify that the critical load distribution is ready to accept power. Ensure

that personnel and equipment are ready for the critical load distribution system to be energized.

NOTE

If the system was shut down in response to an “Emergency Off,” there may be alarm messages

on the touchscreen that describe system conditions before or at the time of the shutdown. Some

or all of the alarm conditions may have been resolved.
To clear these alarm messages, turn Off control power (see

Figure 6

). Wait at least 10 minutes

for the control power circuitry to completely de-energize. After 10 minutes, turn control power

back On.

Содержание Liebert NXL 250 kVA

















































































































Результаты поиска

Содержание Liebert NXL 250 kVA

Отзывы:

Похожие инструкции для Liebert NXL 250 kVA

Бренды по названию

Популярные бренды

Emerson Liebert NXL 250 kVA, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Liebert NXL 250 kVA

Отзывы:

Похожие инструкции для Liebert NXL 250 kVA

Бренды по названию

Популярные бренды