Emerson Liebert NXL 250 kVA Скачать руководство пользователя

Страница: 105 / 112

UPS Alarm and Status Messages

Liebert

NXL

™

Outlet

Ovtemp

Limit

The difference between the inlet air temperature

and the outlet air temperature is too great.

This alarm means excessive heat is being

generated internally resulting in a higher than

normal exhaust air temperature.

If the Bypass is within limits, the UPS reacts to

this alarm by transferring to Bypass and shutting

Off the Inverter.

This alarm is self-clearing. When the condition is

no longer present, the alarm and any control

activity tied to the alarm reverts to normal.

Press “SILENCE” to silence the audible alarm.

Check the Inlet Air Temperature on the One-Line

Display and verify the reading is accurate, i.e. is

the room temperature warmer than normal?

If the room temperature is warmer than normal,

investigate and resolve the issue.

If the room temperature is normal, and the Inlet Air

Temp reading on the One-Line Display is higher

than normal, contact your factory-authorized

service provider.

Output

Fault

This summary event occurs when the detected

system output exceeds acceptable voltage limits.

If the UPS was on Inverter at the time of the

event, the UPS transfers to bypass provided the

bypass voltage is available.

If the UPS was on bypass at the time of the

event, the UPS shuts down rather than allowing

unacceptable voltage to reach the load.

Press “SILENCE” to silence the audible alarm.

Check the Active Event Window and investigate

other events to further analyze.

Press “RESET” to attempt to reset any latched

events.

Check the One-Line Display to determine the

system status (On UPS, Bypass, or Off).

Check the input and bypass (dual input only) and

observe the One-Line color. Green indicates good

power present, orange means power is present but

outside nominal range, and gray means power is

not present.

If the load is Off and the input voltage is ok,

attempt to restart the UPS by pressing “Startup,”

“Manual Start,” and follow the prompts.

If the Input Meter indicates input or bypass is not

available, investigate and resolve the power

problem.

If the load is on bypass and all alarms are reset,

press “Transfer,” “UPS,” to attempt to transfer back

to Inverter.

If the issue cannot be resolved, contact your

factory-authorized service provider.

Output

Over/Under

Frequency

The output frequency has exceeded the output

frequency limit of +/- 0.25 Hz within the bypass

frequency.

This alarm is self-clearing. When the condition is

no longer present, the alarm and any control

activity tied to the alarm reverts to normal.

Press “SILENCE” to silence the audible alarm.

Check the frequency on the Output Meter. If the

frequency is outside the synchronization range,

investigate and resolve the issue.

This alarm is commonly the result of an inverter not

synchronized to the bypass frequency.

If output frequency error persists, contact your

factory-authorized service provider.

Parallel

Comm

Warn

The control has detected a communication

failure on one of the redundant communication

busses. One of the paralleling control

communication busses is no longer

communicating within the system.

Press “SILENCE” to silence the audible alarm.

Power

Supply

Fail

The controls have detected a problem with a

power supply. This is a summary event. There

are several power supplies, most of them

redundant. In most cases, the UPS can operate

normally even with a failed supply.

Press “SILENCE” to silence the audible alarm.

Press “RESET” to attempt to clear the alarm.

Check the Active Event Window to check for other

events that might explain the Power Supply Fail

alarm. For example, if the bypass is not available,

a Power Supply Fail alarm is normal, because the

Bypass Power Supply has no input power.

Contact your factory-authorized service provider.

Table 10

Liebert NXL alarm and status messages

(continued)

Event Message

Event Definition

Recommended Action

Содержание Liebert NXL 250 kVA

















































































































Результаты поиска

Содержание Liebert NXL 250 kVA

Отзывы:

Похожие инструкции для Liebert NXL 250 kVA

Бренды по названию

Популярные бренды

Emerson Liebert NXL 250 kVA, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Liebert NXL 250 kVA

Отзывы:

Похожие инструкции для Liebert NXL 250 kVA

Бренды по названию

Популярные бренды