manualshive.com logo in svg

Emerson 03200106, Руководство по конструкции

Дизайн-руководство Emerson 03200106 предоставляет полезные инструкции по использованию продукта. Скачайте бесплатное руководство с нашего сайта для получения подробной информации о функциях и настройках. Научитесь эффективно использовать Emerson 03200106 благодаря нашему дизайн-руководству. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Safety 

information

Product 

information

Mechanical 

installation

Electrical 

installation

Getting 

started

User Menu A Commissioning

Advanced 

Parameters

Diagnostics Optimization CT MODBUS RTU Technical Data

232

E300 Design Guide

                                                       Issue Number: 1

If 

Position Feedback Initialize 

(

C18

) is set to one any position feedback devices connected to the drive position feedback interfaces or any position 

feedback category option modules will be re-initialized. 

Position Feedback Initialized Indication

 (

C19

) contains flags that represent the initialization state of position feedback devices connected to the drive 

position feedback interfaces or position feedback interfaces on position feedback category option modules. One indicates that the interface is 
initialized and zero indicates that the interface is not initialized. 
The flags are assigned as shown below. 

If no option module, or an option module other than a position feedback category module, is installed in an option module slot then the relevant flag is 
always set to one. If an attempt is made to enable the drive when any of the flags are zero the drive initiates an Encoder 7 trip. If a drive reset is 
initiated, the bits in 

Position Feedback Initialized Indication

 (

C19

) are checked, and if any position feedback devices are not initialized an attempt is 

made to initialize them.
The table below shows the initialization process for different position feedback devices that can be connected to the drive.

C18

Position Feedback Initialize

Mode

RFC-A, RFC-S

Minimum

0

Maximum

1

Default

0

Units

Type

1 Bit Volatile

Update Rate

Background read

Display Format

Standard

Decimal Places

0

Coding

RW, NC

C19

Position Feedback Initialized Indication

Mode

RFC-A, RFC-S

Minimum

0
(Display: 0000000000)

Maximum

1023
(Display: 1111111111)

Default

0
(Display: 0000000000)

Units

Type

16 Bit Volatile

Update Rate

Background write

Display Format

Binary

Decimal Places

0

Coding

RO, NC, PT

Bit 

Position feedback interface 

0

Drive

2

Option slot 1

4

Option slot 2

6

Option slot 3

Encoder types

Initialization process 

AB, FD, FR 

None. Initialization is immediate and is always successful. The position feedback is set to zero on initialization.

AB Servo
FD Servo
FR Servo
SC Servo

The absolute position used to control a motor can only be defined accurately after two different changes of state of the UVW 
commutation signals. Initialization resets the system that ensures that the UVW signals alone will be used to define the motor 
position until the encoder has moved through two valid commutation signal state changes. Initialization is immediate and is 
always successful. The position feedback is set to zero on initialization.

SC

The SINCOS interpolation system must be initialised. Initialization is immediate and is always successful. The position feedback 
is set to zero on initialization.

SC Hiperface
SC EnDat
SC SSI 

Auto-configuration if required except SC SSI. 
The absolute position must be obtained via comms. This may cause a large change in position feedback.
The SINCOS interpolation system must be initialized. This may have a small effect on the position feedback.

EnDat
BiSS
SSI

Auto-configuration if required except SSI. 
The absolute position must be obtained via comms. This may cause a large change in position feedback.

SC SC

The absolute position used to control a motor is obtained from the sine and cosine signals provided for one revolution until the 
marker pulse occurs. The position obtained from the marker pulse is assumed to be a position of zero. Once a marker has 
occurred the incremental position is used and the single turn sine wave signals are ignored. When the position feedback device 
is initialised the single turn sine wave signals are used again until another marker event occurs. No part of the initialization 
process affects the position feedback seen in parameters, except that the SINCOS interpolation system must be initialized which 
may have a small effect on the position feedback. Initialization is immediate and is always successful.

Содержание 03200106











































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 03200106

Vacon NXP/P User Manual preview
NXP/P
Бренд: Vacon Страницы: 168
Raymarine E12019 Installation Manual preview
E12019
Бренд: Raymarine Страницы: 23
Mitsubishi MELDAS HS Series Specifications And Instruction Manual preview
MELDAS HS Series
Бренд: Mitsubishi Страницы: 133
Omron JUNMA SJDE-**APA-OY User Manual preview
JUNMA SJDE-**APA-OY
Бренд: Omron Страницы: 63
Lenze ESMD7514TMF Installation preview
ESMD7514TMF
Бренд: Lenze Страницы: 2
Aiwa PZ3MD Service Manual preview
PZ3MD
Бренд: Aiwa Страницы: 69
Peaco Support 2S-0.5G-B User Manual preview
2S-0.5G-B
Бренд: Peaco Support Страницы: 244
Siemens PXC00-PE96.A Installation Instructions preview
PXC00-PE96.A
Бренд: Siemens Страницы: 2
Siemens MICROMASTER 440 GX Maintenance Instructions preview
MICROMASTER 440 GX
Бренд: Siemens Страницы: 2
Siemens MICRO MASTER Junior Operating Instructions Manual preview
MICRO MASTER Junior
Бренд: Siemens Страницы: 12
Siemens SIDOOR ATD400K Operating Instructions Manual preview
SIDOOR ATD400K
Бренд: Siemens Страницы: 44
Siemens 6SL3860 Reference Manual preview
6SL3860
Бренд: Siemens Страницы: 40
Siemens SIDOOR AT18 Operating Instructions Manual preview
SIDOOR AT18
Бренд: Siemens Страницы: 56
Siemens SED2 VFD Operating Instructions Manual preview
SED2 VFD
Бренд: Siemens Страницы: 64
Siemens SINAMICS G120P Hardware Installation Manual preview
SINAMICS G120P
Бренд: Siemens Страницы: 94
Siemens SINAMICS G110 Operating Instructions Manual preview
SINAMICS G110
Бренд: Siemens Страницы: 92
Siemens FLENDER H3LV Assembly And Operating Instructions Manual preview
FLENDER H3LV
Бренд: Siemens Страницы: 72
Siemens MICROMASTER Reference Manual preview
MICROMASTER
Бренд: Siemens Страницы: 78

Бренды по названию

Популярные бренды

Загрузить еще бренды