Emerson 01100017 Скачать руководство пользователя страница 52

Страница: 52 / 62

Unidrive M200-201 Quick Start Guide

Issue Number: 6

dESt

Two or more parameters are
writing to the same destination
parameter

The

dESt

trip indicates that destination output parameters of two

or more logic functions (Menus 7 and 8) within the drive are
writing to the same parameter.

dr.CF

Drive configuration

Contact the supplier of the drive.

EEF

Default parameters have been
loaded

The

EEF

trip indicates that default parameters have been

loaded. The exact cause/reason of the trip can be identified from
the sub-trip number (see

Drive User Guide

An External trip is initiated

The cause of the trip can be identified from the sub trip number
displayed after the trip string.

Refer to

Drive User Guide

FAN.F

Fan fail

Indicates the fan or fan circuitry has failed

Fi.Ch

File changed

A file has been changed, power cycle to clear the trip

FI.In

Firmware Incompatibility

The user firmware is incompatible with the power firmware.

HFxx trip

Hardware faults

Internal drive hardware fault (see

Drive User Guide

It.Ac

Output current overload timed out
(I

The It.Ac trip indicates a motor thermal overload based on the
output current and motor thermal time constant. The drive will
trip on It.Ac when the accumulator

gets to 100 %.

This can occur when:

•

There is excessive mechanical load

•

Ensure the load is not jammed / sticking

•

Check the load on the motor has not changed

•

Ensure the motor rated current is not zero

It.br

Braking resistor overload timed out
(I

Braking resistor overload has timed out. This can be caused by
excessive braking resistor energy.

no.PS

No power board

No communication between the power and control boards.

O.Ld1

Digital output overload

The total current drawn from 24 V user supply or from the digital
output has exceeded the limit.

O.SPd

Motor frequency has exceeded the
over frequency threshold

Excessive motor speed (typically caused by mechanical load
driving the motor).

Oh.br

Braking IGBT over-temperature

Braking IGBT over-temperature. Detected by thermal model

Oh.dc

DC bus over temperature

DC bus component over temperature based on a software
thermal model.

Oht.C

Control stage over-temperature

Control stage over-temperature detected.

Oht.I

Inverter over temperature based
on thermal model

IGBT junction over-temperature has been detected based on a
software thermal model.

Oht.P

Power stage over temperature

This trip indicates that a power stage over-temperature has
been detected.

Oht.r

Rectifier over temperature

The Oht.r trip indicates that a rectifier over-temperature has
been detected.

OI.A1

Analog input 1 over-current

Current input on analog input 1 exceeds 24 mA.

OI.AC

Instantaneous output over current
detected

The instantaneous drive output current has exceeded.The set
limit.
Possible solutions:
•

Increase acceleration/deceleration rate

•

If seen during autotune reduce the voltage boost

•

Check for short circuit on the output cabling

•

Check integrity of the motor insulation using an insulation
tester

•

Is the motor cable length within limits for the frame size

•

Reduce the values in the current loop gain parameters

Trip

code

Condition

Description

Sub-trip

Reason

External Trip

= 1

Unidrive M200 201 Quick Start Guide English Iss6.book Page 52 Thursday, September 10, 2015 1:48 PM

Содержание 01100017































































Результаты поиска

Содержание 01100017

Отзывы:

Похожие инструкции для 01100017

Бренды по названию

Популярные бренды

Emerson 01100017, Быстрый старт

Результаты поиска

Содержание 01100017

Отзывы:

Похожие инструкции для 01100017

Бренды по названию

Популярные бренды