Emerson 01100017 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 62

background image

Unidrive M200-201 Quick Start Guide

25

Issue Number: 6

5

Keypad and display

The keypad and display provide information to the user regarding the operating status of the drive
and trip codes, and provide the means for changing parameters, stopping and starting the drive, and
the ability to perform a drive reset.

(1)

The Enter button is used to enter parameter view or edit mode, or to accept a parameter edit.

(2 / 5)

The Navigation keys can be used to select individual parameters or to edit parameter values.

(3)

The Stop / Reset key is used to stop and reset the drive in keypad mode. It can also be used to

reset the drive in terminal mode.

(4)

The Start key is used to start the drive in keypad mode.

(6)

The Escape key is used to exit from the parameter edit / view mode.

(7)

The Speed ref pot is used to control the speed reference in keypad mode (only on Unidrive

M201).

Table 5-1 Status indications

Figure 5-1 Unidrive M200 keypad detail

Figure 5-2 Unidrive M201 keypad detail

String

Description

Drive output

stage

inh

The drive is inhibited and cannot be run. The Drive Enable signal
is not applied to the drive enable terminal or is set to 0. The other
conditions that can prevent the drive from enabling are shown as
bits in

Enable Conditions

.

Disabled

rdy

The drive is ready to run. The drive enable is active, but the drive
inverter is not active because the final drive run is not active

Disabled

StoP

The drive is stopped / holding zero speed.

Enabled

S.Loss

Supply loss condition has been detected

Enabled

dc inj

The drive is applying dc injection braking

Enabled

Er

The drive has tripped and no longer controlling the motor. The trip
code appears on the display.

Disabled

UV

The drive is in the under voltage state either in low voltage or high
voltage mode.

Disabled

1

2

3

4

5

6

V A Hz rpm %

1

V A Hz rpm %

7

Unidrive M200 201 Quick Start Guide English Iss6.book Page 25 Thursday, September 10, 2015 1:48 PM

«
...
23
24
25
26
27
...
»

Содержание 01100017































































Отзывы:

Нет отзывов

Похожие инструкции для 01100017

Бренд: Banner Страницы: 15

Бренд: bar Страницы: 2

Бренд: Bard Страницы: 8

Бренд: Bardiani Valvole Страницы: 35

Бренд: Danfoss Страницы: 85

VLT Decentral FCD 300

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 4

VLT 6000 series

Бренд: Danfoss Страницы: 27

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 20

ADAP-KOOL AK-PC 781

Бренд: Danfoss Страницы: 14

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 12

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 96

Бренд: Jabra Страницы: 4

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды