Emerson 01100017 Скачать руководство пользователя страница 54

Страница: 54 / 62

Unidrive M200-201 Quick Start Guide

Issue Number: 6

So.St

Soft start relay failed to close, soft
start monitor failed

Soft start relay in the drive failed to close or the soft start
monitoring circuit has failed.

St.HF

Hardware trip has occurred during
last power down

Hardware trip (HF01 –HF19) has occurred and the drive has
been power cycled. Enter 1299 to

xx.000

to clear trip

Motor thermistor over-temperature

The motor thermistor connected to terminal 14 (digital input 5)
on the control connections has indicated a motor over
temperature.

th.br

Brake resistor over temperature

The th.br trip is initiated if the hardware based braking resistor
thermal monitoring is connected and the resistor overheats.

tH.Fb

Internal thermistor has failed

Internal thermistor has failed.

thS

Motor thermistor short circuit

The motor thermistor connected to terminal 14 (digital input 5)
on the control connections, is short circuit or low impedance
(<50

tun.S

Autotune test stopped before
completion

The drive was prevented from completing an autotune test,
because either the drive enable or the drive run signals were
removed.

tunE.1

Autotune 1

The drive has tripped during a rotating autotune. The cause of
the trip can be identified from the sub-trip number.

Refer to the

Drive User Guide

tunE.3

Autotune 3

RFC-A mode only.

The drive has tripped during a rotating auto-tune or mechanical
load measurement. The cause of the trip can be identified from
the associated sub-trip number.

Refer to the

Drive User Guide

U.OI

User OI ac

The

U.OI

trip is initiated if the output current of the drive exceeds

the trip level set by

User Over Current Trip Level

. Refer to the

Drive User Guide

U.S

User Save error / not completed

The U.S trip indicates that an error has been detected in the
user save parameters saved in non-volatile memory.

US.24

User 24 V supply is not present on
the adaptor interface terminals
(1,2)

US.24

trip is initiated if the User Supply Select is set to 1 and

no user 24 V supply is present on the user 24 V input on the AI-
Backup adaptor. Refer to the

Drive User Guide.

Trip

code

Condition

Description

Sub-trip

Reason

Reserved

The motor did not reach the required
speed during rotating auto-tune or
mechanical load measurement.

Sub-trip

Reason

Measured inertia has exceeded the
parameter range during a mechanical
load measurement.

Reserved

The commutation signals changed in
the wrong direction during a rotating
autotune.

Unidrive M200 201 Quick Start Guide English Iss6.book Page 54 Thursday, September 10, 2015 1:48 PM

Содержание 01100017































































Результаты поиска

Содержание 01100017

Отзывы:

Похожие инструкции для 01100017

Бренды по названию

Популярные бренды

Emerson 01100017, Быстрый старт

Результаты поиска

Содержание 01100017

Отзывы:

Похожие инструкции для 01100017

Бренды по названию

Популярные бренды