Emerson 01100017 Скачать руководство пользователя

Страница: 33 / 62

Unidrive M200-201 Quick Start Guide

Issue Number: 6

Set Pr

00.004

at the required rate of deceleration. Note that larger values produce lower

deceleration. The rate applies in both directions of rotation.

* With Unidrive M201, the default is Pad (5).

Use Pr

00.005

to select the required frequency/speed reference as follows:

00.004 {02.021}

Deceleration Rate 1

Num

VM_ACCEL_RATE s/100 Hz

10.0 s/100 Hz

RFC-A

00.005 {11.034}

Drive Configuration

Txt

AV (0), AI (1), AV.Pr (2), AI.Pr (3),

Preset (4), Pad (5), Pad.Ref (6),

E.Pot (7), torque (8), Pid (9)

AV (0)*

Value

Text

Description

Analog input 1 (voltage) Analog input 2 (voltage) selected by terminal
(Local/Remote)

Analog input 1 (current) or Analog input 2 (voltage) selected by terminal
(Local/Remote)

AV.Pr

Analog input 1 (voltage) or 3 presets selected by terminal

AI.Pr

Analog input 1 (current) or 3 presets selected by terminal

Preset

Four presets selected by terminal

Pad

Keypad reference

Pad.Ref Keypad reference with terminal control

E.Pot

Electronic Potentiometer

torque

Torque mode, Analog input 1 (current frequency reference) or Analog input 2
(voltage torque reference) selected by terminal

Pid

PID mode, Analog input 1 (current feedback source) and Analog input 2
(voltage reference source)

A change to Pr

00.005

is set by pressing the MODE key on exit from parameter edit mode.

The drive must be disabled, stopped or tripped for a change to take place. If Pr

00.005

changed while the drive is running, when the MODE key is pressed on exit from parameter
edit mode, Pr

00.005

will change back to its previous value.

When the setting of Pr

00.005

is changed, the appropriate drive configuration parameters

are set back to their default values.

NOTE

Unidrive M200 201 Quick Start Guide English Iss6.book Page 33 Thursday, September 10, 2015 1:48 PM

Содержание 01100017































































Результаты поиска

Содержание 01100017

Отзывы:

Похожие инструкции для 01100017

Бренды по названию

Популярные бренды

Emerson 01100017, Быстрый старт

Результаты поиска

Содержание 01100017

Отзывы:

Похожие инструкции для 01100017

Бренды по названию

Популярные бренды