Emerson 01100017 Скачать руководство пользователя страница 48

Страница: 48 / 62

Unidrive M200-201 Quick Start Guide

Issue Number: 6

Defines the time constant for the filter applied to the output of the frequency estimator system.

Spin Start Boost

(00.069) is used by the algorithm that detects the frequency of a spinning motor

when the drive is enabled and

Catch A Spinning Motor

(00.033)

≥

1. For smaller motors the default

value of 1.0 is suitable, but for larger motors

Spin Start Boost

(00.069) may need to be increased.

Spin Start Boost

(00.069) is too small the drive will detect zero speed whatever the frequency of the

motor, and if

Spin Start Boost

(00.069) is too large the motor may accelerate away from standstill

when the drive is enabled.

Bit 0:

Stop on defined non-important trips

Bit 1:

Disable braking resistor overload detection

Bit 2

: Disable phase loss stop

Bit 3:

Disable braking resistor temperature monitoring

Bit 4:

Disable parameter freeze on trip. Refer to

Drive User Guide.

Displays the maximum heavy duty current rating of the drive.

00.067 {03.079}

Sensorless Mode Filter

Txt

RFC-A

4 (0), 5 (1), 6 (2), 8 (3), 12 (4),

20 (5) ms

4 (0) ms

00.069 {05.040}

Spin Start Boost

Num

0.0 to 10.0

1.0

RFC-A

00.076 {10.037}

Action On Trip Detection

Num

0 - 31

RFC-A

00.077 {11.032}

Maximum Heavy Duty Rating

Num

0.00 to 9999.99 A

RFC-A

Unidrive M200 201 Quick Start Guide English Iss6.book Page 48 Thursday, September 10, 2015 1:48 PM

Содержание 01100017































































Результаты поиска

Содержание 01100017

Отзывы:

Похожие инструкции для 01100017

Бренды по названию

Популярные бренды

Emerson 01100017, Быстрый старт

Результаты поиска

Содержание 01100017

Отзывы:

Похожие инструкции для 01100017

Бренды по названию

Популярные бренды