Emerson 01100017 Скачать руководство пользователя | Manualshive

Страница: 50 / 62

background image

50

Unidrive M200-201 Quick Start Guide

Issue Number: 6

7

Running the motor

This section takes a new user through all the essential steps to running a motor for the first time.

Table 7-1 Open Loop and RFC-A

Action

Detail

Before power up

Ensure:
•

The drive enable signal is not given, terminal 11 is open

•

The run signal is not given, terminal 12/13 is open

•

The motor is connected to the drive

•

The motor connection is correct for the drive

Δ

or Y

•

The correct supply voltage is connected to the drive

Power up the drive

The default setting is Open Loop vector mode. For RFC-A mode set
Pr

00.079

to RFC-A, then press the

stop/reset button to save

the parameters.
Ensure:
•

The drive displays: Inh

Enter minimum and
maximum speeds

Enter:
•

Minimum speed Pr

00.001

(Hz)

•

Maximum speed Pr

00.002

(Hz)

Enter accel and
decel rates

Enter:
•

Acceleration rate Pr

00.003

(s/100 Hz)

•

Deceleration rate Pr

00.004

(s/100 Hz)

Enter motor
nameplate details

Enter:
•

Motor rated current in Pr

00.006

(A)

•

Motor rated speed in Pr

00.007

(rpm)

•

Motor rated voltage in Pr

00.008

(V)

•

Motor rated power factor in Pr

00.009

•

If the motor is not a standard 50/60 Hz motor, set Pr

00.039

accordingly

Ready to autotune

Autotune

The drive is able to perform either a stationary or a rotating autotune.
The motor must be at a standstill before an autotune is enabled.
To perform an autotune:
•

Set Pr

00.038

= 1 for a stationary autotune or set Pr

00.038

= 2

for a rotating autotune

•

Close the drive enable signal (apply +24 V to terminal 11). The
drive will display ’Rdy’.

•

Close the run signal (apply +24 V to terminal 12 or 13). The
display will flash ’tuning’ while the drive is performing the
autotune.

•

Wait for the drive to display ‘Inh’ and for the motor to come to a
standstill.

•

Remove the drive enable and run signal from the drive.

Autotune complete When the autotune has been completed,

Pr

00.038

will be set to 0

Tuning of frequency
controller gains
(RFC-A mode only)

Depending on the application, the frequency controller gains (Pr

00.065

and Pr

00.066

) may need to be adjusted.

Save parameters

Save parameters

Select ‘SAVE’ in Pr

mm.000

(alternatively enter a value of 1001) and

press the

Stop / Reset button to save parameters.

Ready to run

Run

The drive is now ready to run the motor.

Increasing and
decreasing speed

Turning the speed potentiometer will increase and decrease the
speed of the motor.

Stopping

To stop the motor under ramp control, open either the run forward or
run reverse terminal. If the enable terminal is opened while the motor
is running, the motor will coast to a stop.

0.02

t

100Hz

0.03

t

0.04

Mot X XXXXXXXXX
No XXXXXXXXXX kg

IP55 I.cl F C 40 s S1

°

V

Hz min

-1

kW cos

φ

A

230

400

50 1445 2.20 0.80 8.50

4.90

CN = 14.5Nm

240
415

50 1445 2.20 0.76 8.50

4.90

CN = 14.4Nm

CTP- VEN 1PHASE 1=0,46A P=110W R.F 32MN

I.E

.C

34 1(

87)

cos

∅

σ

L

S

R

S

Unidrive M200 201 Quick Start Guide English Iss6.book Page 50 Thursday, September 10, 2015 1:48 PM

«
...
48
49
50
51
52
...
»

Содержание 01100017































































Отзывы:

Нет отзывов

Похожие инструкции для 01100017

Бренд: Lawler Страницы: 4

Бренд: 1Control Страницы: 8

Бренд: Eaton Страницы: 12

Бренд: ZKTeco Страницы: 2

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: Faro Barcelona Страницы: 8

Бренд: Faro Страницы: 3

Бренд: YASKAWA Страницы: 456

ServeRAID-MR10is

Бренд: IBM Страницы: 94

ServeRAID-4 Ultra160 Series

Бренд: IBM Страницы: 20

8271 Nways Ethernet LAN Switch

Бренд: IBM Страницы: 6

Бренд: IBM Страницы: 86

Бренд: IBM Страницы: 205

Бренд: IBM Страницы: 28

Бренд: National Instruments Страницы: 2

Бренд: Olsberg Страницы: 68

Бренд: Panamax Страницы: 16

Бренд: L-Acoustics Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды