Eaton Fuller FSO-2405 Скачать руководство пользователя

Страница: 130 / 163

130

Front Section Disassembly

Front Section

2nd Ed. 02/07

FSO-2405

FSO-2405/55

FSO-2405/57

Permaglide Bushing

Installation

1. Place the bushing on the proper tool.

NOTE: See “Special Tools”, Ref. E001010.

2. Position the bushing in the bushing bore and

install the bushing by hitting the tool until it rest
against the housing. This condition gives the
proper bushing depth.

3. Use a punch and lock the bushing by punching

the housing material in four positions around
the bushing bore.

WARNING! When locking the bushing, be
careful not to damage the bushing itself.

4. Apply a thin coating of recommended grease

to the bushing inner diameter.

Содержание Fuller FSO-2405




































































































































































Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды

Eaton Fuller FSO-2405, Руководство по обслуживанию

Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды