Eaton Fuller FSO-2405 Скачать руководство пользователя

Страница: 95 / 163

Rear Section Disassembly

FSO-2405

2nd Ed. 02/07

Rear Section

21. Remove the two needle bearings and the

reverse gear spacer from the countershaft.

NOTE: The reverse gear needle bearing on
the countershaft was updated. When
servicing the unit, if older, replace both
bearings (p/n 3342286) and spacer (p/n
3342287) by the new lone bearing (p/n
3348906).

21. Remove the two pivot threaded pins of 5th/

reverse shift yoke.

FSO-2405/13

FSO-2405/14

FSO-2405/155

FSO-2405/154

Old needle bearing

New needle bearing

Old part

2 (two) bearings - Eaton P/N 3342286

1 (one) spacer - Eaton P/N 3342287

New part

1 (one) bearing - Eaton P/N 3348906

Содержание Fuller FSO-2405




































































































































































Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды

Eaton Fuller FSO-2405, Руководство по обслуживанию

Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды