Eaton Fuller FSO-2405 Скачать руководство пользователя

Страница: 108 / 163

108

Rear Section Assembly

Rear Section

2nd Ed. 02/07

FSO-2405

FSO-2405/3

FSO-2405/100

29. Remove the special tool from the mainshaft.

30. Install the rear nut on the mainshaft.

NOTE: When installing the nut, replace the
used nut by a new one.

31. Place the tool to tighten the mainshaft rear nut.

NOTE: See “Special Tools”, Ref. E006006.

NOTE:

As an option, the tool # E006004 or

# E006005 may be used for installing the
mainshaft rear nut, locking the mainshaft
with the tool # E006003. See “Special Tools,
Using the Eaton tool # E006003”.

32. Place the special tool and lock the mainshaft.

NOTE: See “Special Tools”, Ref. E014010.

33. Tighten the mainshaft rear nut to the proper

torque.

NOTE: Torque = 217-270 N.m (160-200 lb.ft)

34. Remove the tools.

36. Install the retaining ball that locks the

speedometer rotor in the mainshaft. Apply
grease to hold the ball in place.

FSO-2405/156

35. Use a punch and lock both the mainshaft and

countershaft rear nuts.

Содержание Fuller FSO-2405




































































































































































Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды

Eaton Fuller FSO-2405, Руководство по обслуживанию

Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды