Eaton Fuller FSO-2405 Скачать руководство пользователя

Страница: 143 / 163

143

Front Section Disassembly

FSO-2405

2nd Ed. 02/07

Front Section

FSO-2405/82

FSO-2405/78

FSO-2405/80

FSO-2405/81

Synchronizer Assemblies

4. Install the synchronizer assemblies with the

hub most prominent side facing the odd speed
gear (either 1st or 3rd depending on the
assemly).

5. Install the synchronizer assemblies with the

sleeve largest chamfer side facing the odd
speed gear (either 1st or 3rd depending on the
assemly).

5th/reverse Speed Synchronizer

6. The 5th/reverse synchronizer hub has an anti-

escape relief on the splines and must be
installed with that relief side facing the 5th
speed gear.

7. The 5th/reverse synchronizer sleeve spline

ends have one side rounded and the other side
sharp ended. Install the 5th/reverse
synchronizer assembly with the sleeve spline
rounded end facing the reverse gear and the
sharp end facing the 5th speed gear.

Содержание Fuller FSO-2405




































































































































































Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды

Eaton Fuller FSO-2405, Руководство по обслуживанию

Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды