Eaton Fuller FSO-2405 страница 104 Скачать руководство пользователя

Страница: 104 / 163

104

Rear Section Assembly

Rear Section

2nd Ed. 02/07

FSO-2405

FSO-2405/13

FSO-2405/15

FSO-2405/99

15. If necessary, replace the 5th/reverse shift yoke

nylon pads.

16. Install the 5th/reverse shift yoke in

synchronizer sleeve groove. Pull the yoke
backwards until engaging with the linked shift
block.

17. Install the two pivot threaded pins of 5th/reverse

shift yoke.

NOTE: Apply

Eaton E677

sealant to the

threads.

Torque = 10-16 N.m (7-12 Lb.ft)

NOTE: See “Special Tools”, Ref. E001044.

18. Install the reverse gear spacer and the two

needle bearings on the countershaft.

NOTE: The reverse gear needle bearing on
the countershaft was updated. When
servicing the unit, if older, replace both
bearings (p/n 3342286) and spacer (p/n
3342287) by the new lone bearing (p/n
3348906).

FSO-2405/14

Содержание Fuller FSO-2405




































































































































































Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды

Eaton Fuller FSO-2405, Руководство по обслуживанию

Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды