Eaton Fuller FSO-2405 Скачать руководство пользователя

Страница: 145 / 163

145

Front Section Assembly

FSO-2405

2nd Ed. 02/07

Front Section

FSO-2405/116

FSO-2405/115

FSO-2405/113

FSO-2405/114

1. Place the front housing with input shaft and

countershaft bearing cups side facing up.

2. Position the 4th speed synchronizer ring on the

input shaft.

NOTE: The 1st, 2nd, 3rd and 4th speed
synchronizer rings are the same and all
coated with EFM II.

3. Install the input shaft with the positioned ring

in the mainshaft front bearing cone. The
synchronizer ring lugs must to slide into the
synchronizer hub key slots.

4. With the input shaft down, position the input

shaft and mainshaft assembly on the front
housing.

5. Position the 3rd/4th speed shift yoke and bar

and the countershaft on the mainshaft
assembly, holding the whole assembly with the
hands.

Содержание Fuller FSO-2405




































































































































































Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды

Eaton Fuller FSO-2405, Руководство по обслуживанию

Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды