Eaton Fuller FSO-2405 Скачать руководство пользователя | Manualshive

Страница: 146 / 163

background image

146

Front Section Assembly

4

Front Section

2nd Ed. 02/07

FSO-2405

FSO-2405/117

FSO-2405/59

FSO-2405/118

6

7

10

8

9

6. Align the whole assembly, as set before, with

the input shaft bear ing cup, with the
countershaft bearing cup and with the 3rd/4th
yoke bar bore, and install the assembly in the
front housing.

NOTE: Be careful to keep the double
shifting interlock balls in place.

7. Install the 1st/2nd shift yoke in the proper

synchronizer sleeve groove.

8. Install the 1st/2nd yoke bar in the bar bore. The

bar notch must be at the lower side.

NOTE: Be careful to keep the double
shifting interlock balls in place.

9. Align the shift yoke with the yoke bar matching

the roll pin holes and install the retaining roll
pin. The 1st/2nd yoke bar notch should be
aligned with the 3rd/4th shift block groove,
formerly installed.

NOTE: Use a 4 mm diameter pin punch.

10. Install the shift selecting bar in the bar bore,

positioning the selecting block shortest arm
between the 1st/2nd yoke bar notch and the
3rd/4th shift block groove. The longest arm must
be ahead the reverse shifting interlocking
mechanism. To do this, rotate the interlocking
mechanism by hand while positioning the shift
selecting bar.

NOTE: Be careful to keep the double
shifting interlock balls in place.

«
...
144
145
146
147
148
...
»

Содержание Fuller FSO-2405




































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Fuller FSO-2405

Бренд: Panasonic Страницы: 32

Бренд: FeiYu Tech Страницы: 8

Бренд: JBL Страницы: 8

Бренд: Viking Страницы: 8

Бренд: Immarsat Страницы: 2

Бренд: Contec Страницы: 15

Бренд: Shure Страницы: 58

Бренд: Bircher Страницы: 4

BeoSound 3000 2671

Бренд: Bang & Olufsen Страницы: 68

Бренд: Bogen Страницы: 12

Бренд: Omnitronic Страницы: 2

Бренд: JTS Страницы: 2

Бренд: Linksys Страницы: 2

Бренд: Kenwood Страницы: 27

Бренд: Kenwood Страницы: 12

Бренд: Kenwood Страницы: 2

Бренд: Kenwood Страницы: 24

Бренд: Kenwood Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды