Eaton Fuller FSO-2405 страница 137 Скачать руководство пользователя

Страница: 137 / 163

137

Front Section Disassembly

FSO-2405

2nd Ed. 02/07

Front Section

Input Shaft Bearing Cup

Removal

1. Place the front housing properly supported

with the input shaft bearing cup removing side
down.

2. Use the bearing cup puller and remove the

bearing cup from the bearing bore.

NOTE: See “Special Tools”, Ref. E012004.

Installation

1. Support properly the front housing with bearing

cup installing side up.

2. Prior installing the bearing cup, carefully clean

bearing cup and bore.

3. Use the proper tool and drive the bearing cup

into the bearing bore, just until the cup be
guided by the bore.

NOTE: See “Special Tools”, Ref. E001033,
E001037, E001039

4. Install the input shaft bearing cover and tighten

the cover retaining capscrews to the proper
torque (see “Input Shaft Bearing Cover -
Installation”).

NOTE: Torque = 10-16 N.m (7-12 lb.ft)

FSO-2405/171

FSO-2405/50

FSO-2405/183

Содержание Fuller FSO-2405




































































































































































Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды

Eaton Fuller FSO-2405, Руководство по обслуживанию

Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды