Eaton Fuller FSO-2405 Скачать руководство пользователя

Страница: 93 / 163

Rear Section Disassembly

FSO-2405

2nd Ed. 02/07

Rear Section

11. Lock the mainshaft again with the special tool

and shift transmission into the 1st gear.

NOTE: See “Special Tools”, Ref. E014010.

NOTE: As an option, the tool # E006003 may
be used for locking the mainshaft. See
"Special Tools, Using the Eaton tool #
E006003".

12. Remove the countershaft rear nut (or snap ring).

NOTE: On 2006, the nut was replaced by a
snap ring in some applications.

NOTA: See “Special Tools”, Ref. E006002.

13. Remove the countershaft ball bearing.

14. Remove the bearing thrust washer.

NOTE: On countershaft with threadless end,
which uses a snap ring instead of the nut,
the thrust washer has a retaining ball (see
detail), which should also be removed.

15. Remove the reverse gear and the ball bearing

together from the mainshaft by pulling them off.

NOTE: See “Special Tools” - Ref. E012001,
E012002.

FSO-2405/5

FSO-2405/138

FSO-2405/153

Содержание Fuller FSO-2405




































































































































































Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды

Eaton Fuller FSO-2405, Руководство по обслуживанию

Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды