Eaton Fuller FSO-2405 страница 121 Скачать руководство пользователя

Страница: 121 / 163

121

Front Section Disassembly

FSO-2405

2nd Ed. 02/07

Front Section

FSO-2405/106

FSO-2405/105

FSO-2405/104

16. Use two tubular tools and press the late

installed set of components of the mainshaft.
Make sure to align the synchronizer ring lugs
with hub key slots.

WARNING! Apply force to bearing inner
race. NEVER apply force to the bearing
cage.

NOTE: See “Special Tools”, Ref. E010001,
E010002.

17. Make sure the pressing procedure was

successfully: disengage the synchronizer and
position it between the 3rd and 4th speed gears.
In this condition, the gears should run free.

Manishaft

18. Install the 3rd/4th synchronizer hub retaining

snap ring.

19. Position the front bearing cone on the

mainshaft.

20. Press the front bearing cone.

WARNING! Apply force to bearing inner
race. NEVER apply force to the bearing
cage.

NOTE: See “Special Tools”, Ref. E010001.

Содержание Fuller FSO-2405




































































































































































Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды

Eaton Fuller FSO-2405, Руководство по обслуживанию

Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды