Eaton Fuller FSO-2405 Скачать руководство пользователя

Страница: 153 / 163

153

Front Section Assembly

FSO-2405

2nd Ed. 02/07

Front Section

FSO-2405/32

FSO-2405/120

FSO-2405/125

33. Remove any remaining sealant material from

housing mounting surfaces.

34. Use either a proper tap or screw and remove

any remaining sealant material from housing
threaded holes.

35. Apply sealant to the front housing mounting

surface. Spread the sealant properly to prevent
leaks.

NOTE: Use

Eaton E680

sealant.

36. Position the shift lug in the gear shift control

tower opening in the intermediate housing, and
install the intermediate housing on the front
housing. The shift lug should be installed on
the shift selecting bar with the cam side facing
right as shown in the picture.

NOTE: If necessary, carefully hit the
housing’s capscrews area with a plastic
hammer to match the housings.

Содержание Fuller FSO-2405




































































































































































Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды

Eaton Fuller FSO-2405, Руководство по обслуживанию

Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды