Eaton Fuller FSO-2405 Скачать руководство пользователя

Страница: 107 / 163

107

Rear Section Assembly

FSO-2405

2nd Ed. 02/07

Rear Section

FSO-2405/141

FSO-2405/138

25. Use the recommended tool and install the rear

ball bearing on the countershaft.

NOTE: See “Special Tools”, Ref. E010001.

26. Use the recommended tool and install the rear

ball bearing on the mainshaft.

NOTE: See “Special Tools”, Ref. E010002.

FSO-2405/5

27.

Lock the mainshaft with the special tool and shift

transmission into the 1st gear.

NOTE: See “Special Tools”, Ref. E014010.

NOTE: As an option, the tool # E006003 may
be used for locking the mainshaft. See
“Special Tools, Using the Eaton tool #
E006003”.

28.

Install the rear nut (or snap ring) on counter-
shaft and tighten to the proper torque.

NOTE: On 2006, the nut was replaced by a
snap ring in some applications.

NOTA:

See “Special Tools”, Ref. E006002.

Torque = 108-122 N.m (80-90 lb.ft)

NOTE: When installing the nut (or the snap
ring), replace the used nut (or used snap
ring) by a new one.

Содержание Fuller FSO-2405




































































































































































Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды

Eaton Fuller FSO-2405, Руководство по обслуживанию

Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды