Duo-Therm 39125 Скачать руководство пользователя страница 21

Страница: 21 / 127

Section B - Operation, cont’d.

Heat Pump Operation

(To set heating temperatures for vehicles equipped with a
Duo-Therm rooftop or basement heat pump, see “Cooling
Mode Operation”.) See FIG. B8.

1. Momentarily depress and release the

MODE

push-button until the

HEAT PUMP

indicator on the LCD

is illuminated.

2. If you have not previously set your fan speed, you may

do so by depressing and releasing the

FAN

push-

button to select.

3. Depress and release the

push-button to increase

the temperature or the

push-button to decrease

the desired temperature. The final selected

SETPOINT

will be displayed in the LCD area of the Comfort Con-
trol Center.

4. After a delay of approximately 2 minutes the heat

pump’s compressor will come on and the heating pro-
cess will begin. Once the room temperature reaches
the selected

SETPOINT

, the compressor will cycle off.

Once the Comfort Control Center senses the need for
heating, the compressor will restart in approximately
two minutes. At this point, the fan will either:
a. continue to operate in the single selected fan speed

or,

b. cycle

OFF

and

with the compressor if the

AUTO

fan speed has been selected.

5. If the vehicle contains more than one

ZONE

, depress

the

FAN

and

MODE

push-buttons simultaneously to

select

ZONE 2

, and repeat procedures from Step 1

above. Repeat entire procedure for each additional
zone.

FIG. B8

Furnace Mode Operation

(If the vehicle is equipped with a gas furnace connected to
the Comfort Control Center.) See FIG. B9

1. Momentarily depress and release the

MODE

push-button until the

FURNACE

indicator on the LCD

is illuminated.

2. The Heat Pump fan does not operate in the

FURNACE

mode.

3. Depress and release the

push-button to increase

the temperature or the

push-button to decrease

the desired temperature. The final selected

SETPOINT

will be displayed in the LCD area of the Comfort Con-
trol Center.

4. The Duo-Therm heat pump system will not operate

when the Comfort Control System is in the

FURNACE

mode. For cooling, change

MODE

COOL

5. If the vehicle contains more than one

ZONE

, depress

the

FAN

and

MODE

push-buttons simultaneously to

select

ZONE 2

, and repeat procedures from Step 1

above. Repeat entire procedure for each additional
zone.

Note:

When furnace mode is selected in any Zone, all heat

pump units will terminate operation.

FIG. B9

B1d. Comfort Control Center

Manual

Compliments

Northwest

Supply

Printed

From

http://www.nwrvsupply.com

Содержание 39125
































































































































Результаты поиска

Содержание 39125

Отзывы:

Бренды по названию

Популярные бренды

Duo-Therm 39125, Руководство по обслуживанию

Результаты поиска

Содержание 39125

Отзывы:

Бренды по названию

Популярные бренды