Duke GES-102 Скачать руководство пользователя страница 67

Страница: 67 / 107

Soft Serve Freezer Model GES-102

184559

15 VQM Error Codes

(continued)

Error Code

Description/Action

Probable Cause

Remedy

CYL RFG.

This error occurs when

cylinder system run time

exceeds 90 minutes.

Cylinder switches to

STBY mode and locks

out.

Action: Cylinder

Refrigeration off, cabinet

refrigeration continues

to operate.

Reset Method: Main

Power Switch, once

the condition has been

rectified.

1. Dirty Condenser

2. Shortage of

Refrigerant

3. Faulty wire

connection

4. Compressor starting

components failure (1

Phase Only)

5. Compressor

Contactor Failure

6. Compressor

Contactor Control Relay

not activating

7. System lacks

efficiency

8.Faulty Thermistor

9. Condenser Fan Motor

Failure (Air Cooled

Only)

1. Clean Condenser

2. Locate Source of refrigerant leak

and repair.

3. Locate faulty connection (Wire

rubbed through, cut) and repair as

needed.

4. Check Compressor Starting

components and replace as needed.

5. Check contactor coil for proper

resistance, check for voltage drop

across contact points. Replace as

needed

6. Check to see if Relay is receiving

power from Main P.C. board (12VDC),

Ohm relay control coil for proper

resistance. Replace relay as needed.

If no 12VDC is detected Contact H.C.

Duke & Son Factory Tech Support.

7. Check for worn blades, AXV

pressure settings, Check water

regulating valve setting (Water

Cooled), check refrigerant level,

compressor efficiency.

8. Remove thermistor, check in ice

water and compare to thermistor curve

chart. If faulty replace, if thermistor

tests o.k. check wire harness

connections. If all connections are

sound possibility of control board

issue. (Contact H.C. Duke & Son for

proper compressor oil charge)

9. Replace Condenser fan motor

Содержание GES-102











































































































Результаты поиска

Содержание GES-102

Отзывы:

Duke GES-102, Руководство оператора с иллюстрированным перечнем запчастей, Страница: 67 / 107

Результаты поиска

Содержание GES-102

Отзывы: