background image

  

DResearch – User Manual TeleObserver MR3180    

 

2011-02-03 

 

55 

 
4.3 

Shutdown behaviour of the system  

4.3.1 

Shutdown behaviour during permanent and alarm recordings 

 

The device distinguishes between two sources for a shutdown requirement (trigger for controlled shut-

down):  Shutdown  requirement  through  ignition  (shut  down  signal)  and  also  shutdown  requirement 

from another source (HD lock or detector e.g. input or motion detection). Depending on the triggering 

source the behaviour differs in normal operation and at a current alarm recording as follows: 
 

 

Trigger: 

ignition (ignition or other shutdown signal) 

Trigger:  

other sources such as HD lock, 

detector, digital input 

Behaviour in  

normal operation: 

 

If the shutdown requirement is not 
cancelled, the system processes the 
configured system follow-up time (which 
can be 0 seconds). If the requirement will 
not be cancelled (restarting the device) 
the system shuts down. 

 

 

The device shuts down. This 
behaviour has priority over the 
system follow-up time.  

 

Behaviour in alarm 

recordings: 

 

As long as an alarm is active, the device 
records into the alarm archives (only in 
the case of longer fitting detectors, not for 
pulse detectors e.g. an alarm button). 

If there is already a shutdown 
requirement and the device is in the 
system follow-up time, the follow-up time 
will be “freezed” during the alarm and 
post-alarm recordings. 

 

After finish of the alarm the device 
records into the alarm archives for the 
configured follow-up time. 

 

After the post-alarm duration the device 
processes the configured system follow-
up time (which can be 0) or continues a 
„frozen“ system follow-up time. 

If the shutdown requirement hasn’t been 
cancelled during this time, the device 
shuts down. If further alarms occur in this 
period the follow-up time will be frozen 
again – the above described process 
takes place again. 

 

The device shuts down. This 
behaviour has priority over 
alarm or post-alarm recordings 
and the system follow-up time

 

 

A  shutdown  requirement  for  the  system  using  HD-lock  switch,  detectors  and/or  digital  switch 
inputs has priority over a currently ongoing alarm recording!  
If an existing shutdown requirement will be cancelled before the end of the alarm (system will be 
switched on again), the device doesn’t shut down – but turns into the normal operation mode after 
processing the alarm and post-alarm time. 

 
 
 

Содержание TeleObserver MR3180



































































Отзывы: